FireCADCalc

Film Condensation on Horizontal Tubes (Nusselt)

Condensing coefficient of steam on a horizontal tube and a vertical row of N tubes by Nusselt's film theory, with IF97 liquid properties.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolChemical and fertiliserIAPWS-IF97 (water and steam)Condenser and cooling tower

Inputs

Examples: 2 bar steam, 25 mm tubesVacuum condenser

Results

Liquid properties at saturation; non-condensable gas sharply lowers the coefficient. Kern's N^−1/6 is a less conservative row correction.

Coefficient, single tube13,168W/(m²·K)
Mean coefficient, row of N tubes (N^−1/4)6,226.8W/(m²·K)
Heat flux, single tube65.840kW/m²

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 2 bar steam, 25 mm tubes. The inputs, in the units selected above:

InputValue
Steam pressure (absolute)2.0000 bar
T_sat − T_wall8.0000 K
Tube outside diameter25.000 mm
Tubes in a vertical row10.000 -

Applying the formula below gives:

ResultValue
Coefficient, single tube13,917 W/(m²·K)
Mean coefficient, row of N tubes (N^−1/4)7,826.4 W/(m²·K)
Heat flux, single tube111.34 kW/m²

Open this example in the calculator and change any input.

Formula

\(h_1 = 0.729\left[\frac{g\rho_l(\rho_l - \rho_v)h'_{fg}k_l^3}{\mu_l \Delta T D}\right]^{1/4}, \quad h_N = h_1 N^{-1/4}\)

Variables

Symbol Meaning SI unit
\(p\) Steam pressure (absolute) Pa
\(\Delta T\) T_sat − T_wall K
\(D\) Tube outside diameter m
\(N\) Tubes in a vertical row -
\(h_1\) Coefficient, single tube W/(m²·K)
\(h_N\) Mean coefficient, row of N tubes (N^−1/4) W/(m²·K)
\(q\) Heat flux, single tube W/m²

Method and standards

Nusselt.

Where it is used

  • Condensers, juice heaters and steam heaters.
  • Teaching condensation.

Common mistakes

  • ΔT taken as steam minus cooling water.

Assumptions and limits

  • Laminar film, pure vapour.
  • Liquid properties at saturation. Incropera (and the vertical-surface calculator here) take them at the film temperature (T_sat + T_wall)/2; for large ΔT the two differ by a few per cent.

References

  • Nusselt film theory for a horizontal cylinder
  • h = 0.729 [g ρ_l(ρ_l − ρ_v) h′_fg k³/(μ ΔT D)]^¼
  • h′_fg = h_fg + 0.68 c_p ΔT
  • row of N tubes × N^−¼ (Incropera); properties from IAPWS-IF97

Questions and answers

Why does the coefficient fall down a tube row?

Condensate from upper tubes thickens the film on lower ones.

Why add 0.68 c_p ΔT?

It accounts for sub-cooling of the condensate film (Rohsenow's modification).

Air in the steam?

Even a small amount of air blankets the tubes and cuts the coefficient a lot.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.