Worked example
Example: 2 mm aluminium, 30 mm, 100 mm wide, h 50, 60 K. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Fin thickness | 2.0000 mm |
| Fin length (base to tip) | 30.000 mm |
| Fin width | 100.00 mm |
| Fin conductivity | 200.00 W/(m·K) |
| Convection coefficient | 50.000 W/(m²·K) |
| Base minus fluid temperature | 60.000 K |
Applying the formula below gives:
| Result | Value |
|---|---|
| Fin parameter √(hP/(kA_c)) | 15.969 1/m |
| Heat flow from the fin | 17.551 W |
| Fin efficiency | 92.569 % |
| Fin effectiveness (vs no fin) | 29.252 |
Open this example in the calculator and change any input.
Formula
\(q_f = \sqrt{hPkA_c}\,\theta_b\,\frac{\sinh mL + (h/mk)\cosh mL}{\cosh mL + (h/mk)\sinh mL}, \quad m = \sqrt{\frac{hP}{kA_c}}\)
\(q_f = \sqrt{hPkA_c}\,\theta_b\,\frac{\tanh mL + h/(mk)}{1 + (h/mk)\tanh mL}, \quad \eta_f = \frac{q_f}{h A_f \theta_b}, \quad \varepsilon_f = \frac{q_f}{h A_c \theta_b}\)
\(A_c = w\,t, \quad P = 2(w + t), \quad A_f = PL + A_c\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(t\) | Fin thickness | m |
| \(L\) | Fin length (base to tip) | m |
| \(w\) | Fin width | m |
| \(k\) | Fin conductivity | W/(m·K) |
| \(h\) | Convection coefficient | W/(m²·K) |
| \(\theta_b\) | Base minus fluid temperature | K |
| \(m\) | Fin parameter √(hP/(kA_c)) | 1/m |
| \(A_c\) | Fin cross-section w t | m² |
| \(P\) | Fin perimeter 2(w + t) | m |
| \(A_f\) | Fin surface including the tip | m² |
| \(q_f\) | Heat flow from the fin | W |
| \(\eta_f\) | Fin efficiency | - |
| \(\varepsilon_f\) | Fin effectiveness (vs no fin) | - |
Method and standards
Fin equation with a convective tip.
Where it is used
- Heat sinks and finned surfaces.
- Heat transfer examinations.
Common mistakes
- Ignoring the tip.
- High h liquids where fins help little.
Assumptions and limits
- Uniform h, steady state.
- Efficiency and effectiveness do not depend on θ_b and are given also when θ_b = 0 (no heat flow). The tanh form of the solution is used, so long or thin fins do not overflow.
References
- Incropera
- DeWitt
- Bergman and Lavine
- Fundamentals of Heat and Mass Transfer
- ch. 3 (fin with convective tip, Table 3.4)
Questions and answers
A 2 mm aluminium fin, 30 mm long, h 50, 60 K above air?
About 18 W per 100 mm width at roughly 93 % efficiency.
Why is aluminium preferred?
High conductivity keeps the fin tip close to base temperature.
When are fins worthwhile?
When h is low (gases): effectiveness well above 2.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.