FireCADCalc

Steam Coil Area to Heat a Tank in a Given Time

Steam coil or jacket area needed to heat a batch of liquid from one temperature to another in a set time, with steam used and the peak steam flow.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationPulp and paperFood, dairy and textileIAPWS-IF97 (water and steam)Tank and drum

Inputs

Examples: 10 t water 20 to 80 °C in 2 h, U 800, 4 bar(a)Oil 25 t, 1900 J/kgK, 30 to 90 °C in 4 h, U 150, 7 bar(a)Process water 5 t, 15 to 60 °C in 1 h, U 1000, 3 bar(a)

Results

Tank heat losses and the tank's own steel are not included; add a margin, and size the steam supply and trap for the peak flow.

Coil area needed4.8211m²
Steam used for the batch1,175.6kg
Average steam flow587.81kg/h
Peak steam flow at the start804.53kg/h
Steam saturation temperature143.61°C

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 10 t water 20 to 80 °C in 2 h, U 800, 4 bar(a). The inputs, in the units selected above:

InputValue
Liquid in the tank10.000 t
Specific heat of the liquid4.1800 kJ/(kg·K)
Starting temperature20.000 °C
Final temperature80.000 °C
Heat-up time wanted2.0000 h
Overall heat transfer coefficient of the coil800.00 W/(m²·K)
Steam pressure in the coil (absolute, saturated)4.0000 bar

Applying the formula below gives:

ResultValue
Coil area needed4.8211 m²
Steam used for the batch1,175.6 kg
Average steam flow587.81 kg/h
Peak steam flow at the start804.53 kg/h
Steam saturation temperature143.61 °C

Open this example in the calculator and change any input.

Formula

\(A = \frac{m\,c_p}{U\,t}\ln\frac{T_s - T_0}{T_s - T_1} \qquad m_s = \frac{m\,c_p (T_1 - T_0)}{h_{fg}} \qquad \dot m_{s,0} = \frac{U A (T_s - T_0)}{h_{fg}}\)

Variables

Symbol Meaning SI unit
\(m\) liquid mass kg
\(c_p\) liquid specific heat J/(kg·K)
\(T_0\) start temperature K
\(T_1\) final temperature K
\(t\) heat-up time s
\(U\) overall coefficient W/(m²·K)
\(p_s\) steam pressure Pa
\(A\) coil area m²
\(m_s\) steam for the batch kg
\(\bar{\dot m}_s\) average steam flow kg/s
\(\dot m_{s,0}\) peak steam flow kg/s
\(T_s\) steam saturation temperature K
\(h_{fg}\) latent heat J/kg

Method and standards

Unsteady batch heating with a condensing medium at constant temperature and constant U, integrated exactly; steam properties from IAPWS-IF97.

Where it is used

  • Process water and chemical tanks.
  • Oil storage heating.
  • Jacketed reactors.

Common mistakes

  • Sizing the trap on average instead of peak flow.
  • Ignoring tank heat losses.
  • Using a U for agitated liquid in a still tank.

Assumptions and limits

  • Well-mixed liquid; condensate leaves saturated; no losses.
  • The coil is at the steam pressure entered. A control valve ahead of the coil lowers the pressure and the steam temperature in the coil: enter the pressure in the coil, not the supply pressure.

References

  • IAPWS-IF97
  • Batch heating with constant U (Kern)

Questions and answers

What coil heats 10 t of water from 20 to 80 °C in 2 hours with 4 bar(a) steam?

4.82 m² at U 800 W/m²K; 1176 kg of steam (588 kg/h average, 805 kg/h at the start).

Why is the peak higher than the average?

The liquid is coldest at the start, so the temperature difference and heat flow are largest then.

What U should I use?

From the coil supplier or a heat transfer calculation; agitation raises it a lot.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.