Worked example
Example: Paper 10 t/h wet at 55 % moisture to 8 %, 60 % efficiency, 4 bar(a). The inputs, in the units selected above:
| Input | Value |
|---|---|
| Wet product feed | 10,000 kg/h |
| Moisture in, wet basis | 55.000 % |
| Moisture out, wet basis | 8.0000 % |
| Product (water) temperature in | 50.000 °C |
| Evaporation temperature (wet-bulb or boiling) | 80.000 °C |
| Dryer thermal efficiency | 60.000 % |
| Heating steam pressure (absolute, saturated) | 4.0000 bar |
Applying the formula below gives:
| Result | Value |
|---|---|
| Steam consumption | 9,712.9 kg/h |
| Water evaporated | 5,108.7 kg/h |
| Steam per kg of water evaporated | 1.9013 kg/kg |
| Heat supplied | 5,755.8 kW |
Open this example in the calculator and change any input.
Formula
\(\dot W = \dot m_1 - \dot m_1\frac{1 - x_1}{1 - x_2} \qquad \dot Q = \frac{\dot W\,[h_g(T_{ev}) - h_l(T_1)]}{\eta_d} \qquad \dot m_s = \frac{\dot Q}{h_{fg}(p_s)}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot m_1\) | wet feed | kg/s |
| \(x_1\) | moisture in, wet basis | – |
| \(x_2\) | moisture out, wet basis | – |
| \(T_1\) | water temperature in; \(h_l(T_1)\) is taken at 101.325 kPa | K |
| \(T_{ev}\) | evaporation temperature | K |
| \(\eta_d\) | dryer thermal efficiency | – |
| \(p_s\) | steam pressure | Pa |
| \(\dot m_s\) | steam consumption | kg/s |
| \(\dot W\) | water evaporated | kg/s |
| \(\dot m_s/\dot W\) | steam per kg water | kg/kg |
| \(\dot Q\) | heat supplied | W |
| \(h_g, h_l, h_{fg}\) | water and steam enthalpies (IF97) | J/kg |
Method and standards
Solids balance for the water removed; heat to warm and evaporate it divided by a dryer efficiency; steam latent heat from FireCAD's IAPWS-IF97.
Where it is used
- Steam budgets of paper machines, textile stenters and food dryers.
- Comparing dryer performance.
- Sizing steam supply and condensate systems.
Common mistakes
- Mixing wet-basis and dry-basis moisture.
- Using an efficiency from another dryer type.
- Ignoring the product's own sensible heat.
Assumptions and limits
- Steady operation; efficiency covers air, product and losses. The sensible heat of the dry solids is not calculated separately; it is inside the efficiency.
- The steam gives up only its latent heat: the condensate leaves saturated at the steam pressure, and flash or condensate heat recovery is not credited.
- The water in the feed is liquid at atmospheric pressure, so its temperature in must be below 100 °C.
References
- Solids and energy balance
- IAPWS R7-97 IF97
Questions and answers
How much steam does a dryer use?
10 t/h of wet paper at 55 % moisture dried to 8 % evaporates 5.1 t/h of water; at 60 % dryer efficiency with 4 bar(a) steam it uses 9.7 t/h of steam, 1.9 kg per kg of water.
Why more than 1 kg of steam per kg of water?
Besides evaporating the water the steam heats air, product and losses; the efficiency covers them.
How do I cut it?
Press out more water mechanically first, recover exhaust air heat, and keep condensate drainage good so the dryer surface stays hot.
Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.