FireCADCalc

CO₂ from O₂ in Flue Gas (and CO₂ max)

CO₂ in dry flue gas for a given O₂ reading, the maximum CO₂ at stoichiometric combustion and the excess air, from the fuel's ultimate analysis.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalPulp and paperASME PTC 4 (fired steam generators)BoilerBurner and furnace

Inputs

Examples: Indian coal, 5 % O2Fuel oil, 3 % O2Bagasse, 6 % O2

Ultimate analysis, as fired, by mass

Results

CO₂ in dry flue gas14.267%
Maximum CO₂ (stoichiometric)19.993%
Excess air39.654%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Indian coal, 5 % O2. The inputs, in the units selected above:

InputValue
O₂ in dry flue gas5.0000 %
Carbon45.000 %
Hydrogen3.5000 %
Oxygen5.0000 %
Nitrogen1.0000 %
Sulphur0.50000 %
Ash35.000 %
Moisture10.000 %

Applying the formula below gives:

ResultValue
CO₂ in dry flue gas13.793 %
Maximum CO₂ (stoichiometric)18.117 %
Excess air30.356 %

Open this example in the calculator and change any input.

Formula

\(n_{O_2} = \frac{C}{M_C} + \frac{H}{2 M_{H_2}} + \frac{S}{M_S} - \frac{O}{M_{O_2}} \qquad n_a = \frac{n_{O_2}}{0.2095}\)

\(n_{d,0} = \frac{C}{M_C} + \frac{S}{M_S} + \frac{N}{M_{N_2}} + 0.7905\,n_a \qquad EA = \frac{O_2\,n_{d,0}}{n_a\,(0.2095 - O_2)}\)

\(CO_2 = \frac{C/M_C}{n_{d,0} + EA\,n_a} \qquad CO_{2,max} = \frac{C/M_C}{n_{d,0}}\)

Variables

Symbol Meaning SI unit
\(O_2\) O₂ in dry flue gas –
\(C\), \(H\), \(O\), \(N\), \(S\), \(A\), \(M\) ultimate analysis as fired, mass fractions (A and M only complete the 100 % check) –
\(CO_2\) CO₂ in dry flue gas –
\(CO_{2,max}\) maximum CO₂ (stoichiometric) –
\(EA\) excess air –
\(n_{O_2}\) oxygen needed per kg of fuel kmol/kg
\(n_a\) theoretical air per kg of fuel kmol/kg
\(n_{d,0}\) dry flue gas at zero excess air kmol/kg
\(M_C\), \(M_{H_2}\), \(M_S\), \(M_{O_2}\), \(M_{N_2}\) molar masses kg/kmol

Method and standards

Dry flue gas balance with air of 20.95 % O₂ and 79.05 % "atmospheric nitrogen" (N₂, Ar and CO₂ of air) as in ASME PTC 4; molar masses from IUPAC 2013 atomic weights.

Where it is used

  • Converting old CO₂-based (Orsat) records to O₂.
  • Checking two analysers against each other.
  • Combustion tuning when only a CO₂ meter is fitted.

Common mistakes

  • Comparing CO₂ readings between different fuels.
  • Mixing wet and dry readings.
  • Ignoring air leakage before the probe.

Assumptions and limits

  • Complete combustion (no CO); dry basis; sulphur counted as SO₂ but not in the CO₂ reading; the 0.04 % CO₂ of the air is counted with the nitrogen.
  • The analysis must sum to 100 %. Ash and moisture do not enter the dry gas balance: the result depends only on the ratios of C, H, O, N and S.
  • An Orsat (KOH) reading absorbs CO₂ and SO₂ together; for a high-sulphur fuel compare it with CO₂ plus the SO₂ share.

References

  • Combustion stoichiometry of the dry flue gas
  • ASME PTC 4 air composition

Questions and answers

How is CO₂ related to O₂ in flue gas?

Both come from the same air and fuel balance. For coal with 45 % carbon at 5 % O₂ (30 % excess air), the dry flue gas holds 13.8 % CO₂; with no excess air it would hold the fuel's maximum, 18.1 %.

Why does CO₂ max depend on the fuel?

Fuels with more hydrogen form water, which leaves the dry gas, but also need more air per kg of carbon. Natural gas peaks near 12 %, oil near 15–16 %, coal near 18–19 %.

Should I control on O₂ or CO₂?

O₂: it depends little on the fuel, while the same CO₂ means different excess air for different fuels.

Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.