FireCADCalc

Mill Roller Surface Speed and Escribed Volume

Peripheral speed of a mill roller from its diameter and speed, and the escribed volume per hour through a work opening of a given length.

Sugar mill and cogeneration

Inputs

Examples: 1070 x 2130 mill, 5 rpmSmall mill

Results

Fibre throughput divided by the escribed volume is the fibre loading (kg/m³) used to set mill openings.

Hugot's speed limits (D in m, speeds in m/min) hold for D from 0.6 to 1.5 m.

Roller surface speed16.808m/min
Escribed volume25.776m³/h
Hugot maximal peripheral speed 33D/(D + 0.73)19.617m/min
Hugot maximal roller speed5.8357rpm
Hugot economic peripheral speed 30D/(D + 0.73)17.833m/min

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1070 x 2130 mill, 5 rpm. The inputs, in the units selected above:

InputValue
Roller mean diameter1.0700 m
Roller speed5.0000 rpm
Roller length2.1300 m
Work opening12.000 mm

Applying the formula below gives:

ResultValue
Roller surface speed16.808 m/min
Escribed volume25.776 m³/h
Hugot maximal peripheral speed 33D/(D + 0.73)19.617 m/min
Hugot maximal roller speed5.8357 rpm
Hugot economic peripheral speed 30D/(D + 0.73)17.833 m/min

Open this example in the calculator and change any input.

Formula

\(v = \pi D n, \quad \dot V = v L g\)

\(V_M = \frac{33D}{D + 0.73}, \quad n_M = \frac{V_M}{\pi D} = \frac{10.5}{D + 0.73}, \quad V_E = \frac{30D}{D + 0.73} \;[\mathrm{m/min};\ D\ \mathrm{m}]\)

Variables

Symbol Meaning SI unit
\(D\) Roller mean diameter m
\(n\) Roller speed 1/s
\(L\) Roller length m
\(g\) Work opening m
\(v\) Roller surface speed m/s
\(\dot V\) Escribed volume m³/s
\(V_M\) Hugot maximal peripheral speed 33D/(D + 0.73) m/s
\(n_M\) Hugot maximal roller speed 1/s
\(V_E\) Hugot economic peripheral speed 30D/(D + 0.73) m/s

Method and standards

Kinematics.

Where it is used

  • Mill setting.
  • Capacity checks.

Common mistakes

  • rpm entered as rev/s.

Assumptions and limits

  • Rigid rollers.
  • Hugot's maximal and economic speeds are shown only for diameters of 0.6–1.5 m, and a note compares the surface speed with the maximal speed.

References

  • v = π D n; escribed volume = v L g (Hugot, Handbook of Cane Sugar Engineering, milling)
  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (1986)
  • ch. 11
  • eqns 11.5–11.9 (maximal and economic speeds)
  • pp. 178–185

Questions and answers

Typical surface speed?

Around 12–20 m/min for most tandems.

Why escribed volume?

It links mill setting to the fibre the mill must pass.

Mean diameter?

Use the mean between groove tops and bottoms.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.