FireCADCalc

Mill Fibre Loading and Capacity Ratio (Hugot)

Fibre loading, specific fibre loading, Hugot's normal specific loading and the capacity ratio of a mill (eqns 12.11–12.14), showing how hard the mill is worked.

Sugar mill and cogeneration

Inputs

Examples: Hugot p. 311: 130 TCH, 12.5 % fibre, 12.5 m/min250 TCH on 1067 x 2134

Results

θ below 1: the mill works under its normal capacity; above 1: overloaded, with extraction falling.

Fibre loading12.928kg/m²
Specific fibre loading q/D15.921kg/m³
Normal specific fibre loading (eqn 12.12)17.172kg/m³
Capacity ratio τ/τ₀0.92712
Peripheral speed12.500m/min

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Hugot p. 311: 130 TCH, 12.5 % fibre, 12.5 m/min. The inputs, in the units selected above:

InputValue
Crushing rate130.00 t/h
Fibre % cane12.500 %
Roller speed4.9001 rpm
Roller diameter0.81200 m
Roller length1.6760 m
Cane preparationTwo knife sets and a shredder (1.22)
Total rollers in the tandem15.000 -

Applying the formula below gives:

ResultValue
Fibre loading12.928 kg/m²
Specific fibre loading q/D15.921 kg/m³
Normal specific fibre loading (eqn 12.12)17.172 kg/m³
Capacity ratio τ/τ₀0.92712
Peripheral speed12.500 m/min

Open this example in the calculator and change any input.

Formula

\(q = \frac{A f}{\pi D n L}, \quad \tau = \frac{q}{D}, \quad \tau_0 = 4.774\,c\,(1 - 0.06\,nD)\sqrt N, \quad \theta = \frac{\tau}{\tau_0}\)

In the τ₀ formula n is in rpm and D in metres (the page converts n from 1/s); 4.774 is close to 15/π.

Variables

Symbol Meaning SI unit
\(A\) Crushing rate kg/s
\(f\) Fibre % cane -
\(n\) Roller speed 1/s
\(D\) Roller diameter m
\(L\) Roller length m
\(c\) Cane preparation -
\(N\) Total rollers in the tandem -
\(q\) Fibre loading kg/m²
\(\tau\) Specific fibre loading q/D kg/m³
\(\tau_0\) Normal specific fibre loading (eqn 12.12) kg/m³
\(\theta\) Capacity ratio τ/τ₀ -
\(v\) Peripheral speed m/s

Method and standards

Continuity of fibre through the roller surface and Hugot's normal loading.

Where it is used

  • Checking mill loading against capacity.
  • Setting mill openings.

Common mistakes

  • Using rpm in the SI form of q.
  • Using fibre % bagasse instead of % cane.

Assumptions and limits

  • 3-roller mills at normal settings.
  • The speed term (1 − 0.06 n D) takes n in rpm.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 12
  • eqns 12.11–12.14
  • pp. 195–197; worked example p. 311

Questions and answers

What is fibre loading?

Fibre passing per square metre of roller surface swept: the mass of fibre in the blanket per unit roller area.

Why divide by D?

Specific fibre loading q/D compares mills of different sizes; normal values lie near 15–20 kg/m³.

What does θ tell me?

The ratio of actual to Hugot's normal loading: above 1 the mill is pushed beyond its comfortable capacity.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.