FireCADCalc

Milling Tandem Capacity (Hugot's Formula)

Crushing capacity of a milling tandem from roller size and speed, number of rollers, fibre and cane preparation, by Hugot eqn 12.6 with his Table 12.1 coefficients.

Sugar mill and cogeneration

Inputs

Examples: 15 rollers 914 x 1829, knives and shredder12 rollers, one knife set, no arcing

Results

Hugot's formula is for 3-roller mills at normal settings and pressures; take it as the capacity the tandem handles without strain.

Preparation coefficient1.2200
Crushing capacity162.62t/h
Daily capacity with 1 % stops (23.75 A)3,862.2t/d
Fibre rate23.580t/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 15 rollers 914 x 1829, knives and shredder. The inputs, in the units selected above:

InputValue
Cane preparationTwo knife sets and a shredder (1.22)
Roller speed5.0000 rpm
Roller diameter0.91400 m
Roller length1.8290 m
Total rollers in the tandem (crusher rollers included)15.000 -
Fibre % cane14.500 %
Top roller arcingArcing fitted (normal)

Applying the formula below gives:

ResultValue
Preparation coefficient1.2200
Crushing capacity162.62 t/h
Daily capacity with 1 % stops (23.75 A)3,862.2 t/d
Fibre rate23.580 t/h

Open this example in the calculator and change any input.

Formula

\(A = \frac{0.9\,c\,n\,(1 - 0.06\,nD)\,L D^2 \sqrt N}{f}\,k_a \;[\mathrm{t/h};\ n\ \mathrm{rpm};\ L, D\ \mathrm{m};\ f\ \text{as a fraction}]\)

\(k_a = 1\) with arcing fitted, \(0.95\) without.

Variables

Symbol Meaning SI unit
\(c\) Cane preparation -
\(n\) Roller speed 1/s
\(D\) Roller diameter m
\(L\) Roller length m
\(N\) Total rollers in the tandem (crusher rollers included) -
\(f\) Fibre % cane -
\(\text{arcing}\) Top roller arcing -
\(A\) Crushing capacity kg/s
\(A_d\) Daily capacity with 1 % stops (23.75 A) kg/s
\(A f\) Fibre rate kg/s
\(k_a\) Arcing factor (1 with arcing, 0.95 without) -

Method and standards

Hugot's empirical capacity formula, eqn 12.6, with the fibre coefficients of Table 12.1 (Handbook of Cane Sugar Engineering, 3rd ed., pp. 190–191). The formula assumes the rollers are regularly arced; where they are not, Hugot (p. 191) applies a coefficient of 0.95 (k_a).

Where it is used

  • Rating existing tandems.
  • First sizing of mills for a new crush.

Common mistakes

  • Counting only the mills instead of all rollers for N.
  • Entering fibre as a percentage number.

Assumptions and limits

  • Hugot's formula; normal settings and imbibition.
  • f is fibre per unit cane as a fraction (0.145, not 14.5); entering a percentage number would give a capacity 100 times too small. The page takes it in % and converts.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 12
  • eqn 12.6 and Table 12.1
  • pp. 186–191

Questions and answers

Why does capacity rise with D² but not D³?

The roller length and surface speed carry the blanket; Hugot fits D² with a speed term (1 − 0.06 nD) that limits fast large rollers.

What is the √N term?

Each extra pressing lets the tandem run thicker blankets; Hugot finds capacity grows with the square root of the number of rollers.

Which c to use?

From Table 12.1: about 1.10 for one wide knife set up to 1.22 for two knife sets and a shredder.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.