Worked example
Example: Hugot example E 79, E0 61. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Working feed opening | 79.000 mm |
| Empty feed opening | 61.000 mm |
| Top roller angle | 70.000 ° |
| Roller diameter | 0.91400 m |
Applying the formula below gives:
| Result | Value |
|---|---|
| Clearance at the toe (feed side), working | 118.50 mm |
| Clearance at the middle, working | 138.25 mm |
| Clearance at the heel, working | 150.10 mm |
| Clearance at the tip (delivery side) | 63.200 mm |
| Toe clearance, empty | 96.900 mm |
| Middle clearance, empty | 115.75 mm |
| Heel clearance, empty | 128.50 mm |
| Trashplate angle α/6 | 11.667 ° |
| Offset 0.00145 D α (α in degrees) | 92.771 mm |
Open this example in the calculator and change any input.
Formula
\(A = 1.50E_A,\ M = 1.75E_A,\ Z = 1.90E_A,\ T = 0.80E_A\)
\(A_0 = A - 1.2\Delta E,\ M_0 = M - 1.25\Delta E,\ Z_0 = Z - 1.2\Delta E,\ \beta = \frac{\alpha}{6},\ MB = 0.00145\,D\,\alpha\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(E_A\) | Working feed opening | m |
| \(E_0\) | Empty feed opening | m |
| \(\alpha\) | Top roller angle | rad |
| \(D\) | Roller diameter | m |
| \(A\) | Clearance at the toe (feed side), working | m |
| \(M\) | Clearance at the middle, working | m |
| \(Z\) | Clearance at the heel, working | m |
| \(T\) | Clearance at the tip (delivery side) | m |
| \(A_0\) | Toe clearance, empty | m |
| \(M_0\) | Middle clearance, empty | m |
| \(Z_0\) | Heel clearance, empty | m |
| \(\beta\) | Trashplate angle α/6 | rad |
| \(MB\) | Offset 0.00145 D α (α in degrees) | m |
Method and standards
Hugot's proportions per 100 of feed opening.
Where it is used
- Setting trashplates at the start of season.
- Diagnosing trashplate chokes.
Common mistakes
- Using the delivery opening as the base.
- Forgetting to correct for the empty position.
Assumptions and limits
- Hugot's proportions for normal 3-roller mills.
- In MB = 0.00145 D α the roller diameter D is in metres and α in degrees, giving MB in metres (93 mm for the default).
- Empty clearances that would come out negative are rejected.
References
- Hugot
- Handbook of Cane Sugar Engineering
- 3rd ed. (Elsevier, 1986)
- ch. 13
- eqns 13.11–13.12 and Table 13.9
- pp. 217–222
Questions and answers
Why is the heel clearance largest?
The blanket swells on the trashplate after leaving the feed nip; the passage widens towards the delivery roller to avoid choking.
What are A, M, Z and T?
Hugot's clearances between the trashplate and the top roller at the toe, middle, heel and the tip at the delivery roller.
Why are empty clearances smaller?
With the mill stopped the top roller sits lower; the feed-side clearances drop about 1.2 times the change of the feed opening.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.