Worked example
Example: 300 t on 1067 x 2134, 20 mm. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Load on the top roller (one opening) | 300.00 tf |
| Roller length | 2.1340 m |
| Roller diameter | 1.0670 m |
| Work opening | 20.000 mm |
| Compression ratio (compressed / initial volume) | 0.10000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Maximum pressure under the roller | 288.70 kgf/cm² |
| Deerr static pressure for c (eqn 10.48) | 70.000 kgf/cm² |
| Deerr exponent at that pressure | 5.1159 |
| Pressure in the mill for c (eqn 10.50) | 88.000 kgf/cm² |
Open this example in the calculator and change any input.
Formula
\(p_M = \frac{3F}{L\sqrt{D\,e_A}}, \quad p_D = \frac{70}{(10c)^n},\ n = 6 - \frac{5800}{p_D^2 + 1660}, \quad p_J = \frac{88}{(10c)^6} \;[\mathrm{kg/cm^2}]\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(F\) | Load on the top roller (one opening) | N |
| \(L\) | Roller length | m |
| \(D\) | Roller diameter | m |
| \(e_A\) | Work opening | m |
| \(c\) | Compression ratio (compressed / initial volume) | - |
| \(p_M\) | Maximum pressure under the roller | Pa |
| \(p_D\) | Deerr static pressure for c (eqn 10.48) | Pa |
| \(n\) | Deerr exponent at that pressure | - |
| \(p_J\) | Pressure in the mill for c (eqn 10.50) | Pa |
Method and standards
Hugot's pressure distribution under the roller (eqn 10.67) and Deerr's and Jenkins' compression laws for bagasse (Hugot eqns 10.48–10.50, pp. 146–149). Deerr's law is fitted to his static tests (Table 10.2) and tabulated by Hugot for 1 to 1 000 kg/cm² (Table 10.3, c from 0.543 to 0.064). Hugot gives the exponent-6 form, used by Jenkins for mill conditions, for pressures of 50 kg/cm² and above.
Where it is used
- Understanding mill pressures and settings.
- Comparing static and mill compression.
Common mistakes
- Using the total hydraulic load for one opening when it divides between feed and delivery.
- Using percentages for c.
Assumptions and limits
- Empirical compression laws for bagasse. A note appears when c is outside 0.064–0.543 (Deerr) or when p_J is below 50 kg/cm² (c above about 0.11), outside the ranges Hugot gives. The load-based p_M and the compression-based p_D and p_J are independent.
- c is h/H (eqn 10.46); Hugot notes de Boer's objection that this is not the true compression in the mill (p. 150).
- Deerr's implicit equation is solved after checking that it has a single root.
References
- Hugot
- Handbook of Cane Sugar Engineering
- 3rd ed. (Elsevier, 1986)
- ch. 10
- eqns 10.48–10.50 (Deerr, Jenkins)
- Tables 10.2–10.3
- pp. 146–149
- and eqn 10.67
Questions and answers
Why is the maximum pressure so much above the specific pressure?
The load acts on a narrow strip near the axial plane, not on the whole projected area.
What is the compression ratio c?
Compressed volume over the initial volume of the bagasse; 0.1 means squeezed to a tenth.
Why does Deerr's exponent vary?
Bagasse stiffens as it is squeezed: n rises from about 2.5 at low pressure towards 6.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.