FireCADCalc

Sucrose Extracted % Cane and Bagasse Pol Check

Sucrose lost in bagasse and extracted per 100 cane (Hugot eqn 21.24), extraction, and the check of bagasse pol against last-roller juice pol (eqn 21.17).

Sugar mill and cogeneration

Inputs

Examples: TypicalPoor last mill

Results

With well-mixed imbibition the bagasse pol would be half the last-roller juice pol (σ = s/2); about 0.7 s is usual, and σ ≥ s shows poor mixing.

Sucrose in bagasse % cane0.53265%
Sucrose extracted % cane12.967%
Extraction c/R96.054%
Bagasse pol / last-roller juice pol0.69231

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Typical. The inputs, in the units selected above:

InputValue
Sucrose % cane13.500 %
Sucrose % bagasse1.8000 %
Fibre % cane14.500 %
Fibre % bagasse49.000 %
Pol % juice extracted by the last roller2.6000 %

Applying the formula below gives:

ResultValue
Sucrose in bagasse % cane0.53265 %
Sucrose extracted % cane12.967 %
Extraction c/R96.054 %
Bagasse pol / last-roller juice pol0.69231

Open this example in the calculator and change any input.

Formula

\(\beta = \sigma\frac{f}{f'}, \quad c = R - \beta, \quad e = \frac{c}{R}\)

Variables

Symbol Meaning SI unit
\(R\) Sucrose % cane -
\(\sigma\) Sucrose % bagasse -
\(f\) Fibre % cane -
\(f'\) Fibre % bagasse -
\(s\) Pol % juice extracted by the last roller -
\(\beta\) Sucrose in bagasse % cane -
\(c\) Sucrose extracted % cane -
\(e\) Extraction c/R -
\(\sigma/s\) Bagasse pol / last-roller juice pol -

Method and standards

Hugot's balance with constant fibre.

Where it is used

  • Daily mill reports.
  • Checking imbibition mixing at the last mill.

Common mistakes

  • Using pol % juice for σ.
  • Using bagasse % cane from an unbalanced weight.

Assumptions and limits

  • Constant fibre through the mills.
  • Sucrose and pol are used interchangeably, as in factory control (apparent sucrose = pol); σ/s compares a sucrose with a pol figure on that basis.
  • Sucrose in bagasse must stay below sucrose in cane.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 21
  • eqns 21.17 and 21.24
  • pp. 337–341

Questions and answers

Why use fibre ratios?

Bagasse % cane equals fibre % cane over fibre % bagasse, so sucrose in bagasse % cane needs no bagasse weight.

What should bagasse pol be?

Below the last-roller juice pol: ideally half, usually about 0.7 of it.

Is this the same as mill extraction?

Yes when R is sucrose (or pol) % cane from the same balance.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.