FireCADCalc

Mill Gearing: Ratio, Roller Speed and Pitch-Line Speed

Roller speed and overall reduction of a mill drive from motor speed, reducer ratio and final pinion and gear teeth, with surface and pitch-line speeds.

Sugar mill and cogenerationElectric motor

Inputs

Examples: Hugot example 1000 rpm, 42.5 : 1, 21/104Turbine reducer drive

Results

Hugot: spur gears up to about 700–825 m/min pitch-line speed; at most about 5 : 1 per spur stage, 10 : 1 for double helical gears.

The final pair's ratio 5.65 : 1 is above Hugot's 5 : 1 for one spur stage.

Roller speed4.2500rpm
Overall reduction141.18
Roller surface speed14.246m/min
Pitch-line speed of the final gear38.720m/min

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Hugot example 1000 rpm, 42.5 : 1, 21/104. The inputs, in the units selected above:

InputValue
Motor or turbine-reducer output speed1,000.0 rpm
Reducer ratio42.500 -
Final pinion teeth21.000 -
Final gear (spur wheel) teeth104.00 -
Top roller diameter0.76200 m
Pitch diameter of the final gear2.4000 m

Applying the formula below gives:

ResultValue
Roller speed4.7511 rpm
Overall reduction210.48
Roller surface speed11.374 m/min
Pitch-line speed of the final gear35.823 m/min

Open this example in the calculator and change any input.

Formula

\(i = i_1\frac{z_2}{z_1}, \quad n = \frac{n_m}{i}, \quad v = \pi D n, \quad v_g = \pi d_g n\)

Variables

Symbol Meaning SI unit
\(n_m\) Motor or turbine-reducer output speed 1/s
\(i_1\) Reducer ratio -
\(z_1\) Final pinion teeth -
\(z_2\) Final gear (spur wheel) teeth -
\(D\) Top roller diameter m
\(d_g\) Pitch diameter of the final gear m
\(n\) Roller speed 1/s
\(i\) Overall reduction -
\(v\) Roller surface speed m/s
\(v_g\) Pitch-line speed of the final gear m/s

Method and standards

Gear train kinematics.

Where it is used

  • Checking drive trains after a speed change.
  • Choosing pinion and gear teeth.

Common mistakes

  • Inverting the tooth ratio.
  • Using the pinion diameter for the roller-shaft gear.

Assumptions and limits

  • Rigid gear train; no slip. Notes compare the final pair with Hugot's limits (pitch-line speed and 5 : 1 per spur stage); the reducer's own stages are not checked.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 17
  • mill gearing
  • pp. 253–258 (example: 1000 rpm, 42.5 : 1 reducer, 21/104 final pair)

Questions and answers

How many stages?

Motors at 485–730 rpm need about 125 : 1 to reach 3–6 rpm, usually three stages; turbines add a high-speed reducer.

Why count teeth, not diameters?

The ratio of a gear pair is fixed by its teeth; pitch diameters follow from the module.

Is pitch-line speed a limit here?

Not for the slow final gear; it matters for the faster spur stages, which Hugot limits to about 700–825 m/min.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.