FireCADCalc

Kraft Mill Chemical Make-Up: Saltcake or Caustic for Soda Losses

Make-up Na₂SO₄ (saltcake) or NaOH needed to replace sodium lost from the kraft liquor cycle, from the soda loss per tonne of pulp expressed as Na₂O (Smook ch. 10).

Pulp and paper

Inputs

Examples: 12 kg Na2O/ADt, 1000 ADt/d, half saltcakeAll caustic make-up

Results

Saltcake also adds sulphur: balance it against the sulfidity target; modern mills with low losses often make up with caustic.

Saltcake is only partly reduced in the recovery boiler: the sodium is all recovered, but less sulphur than shown ends up as Na₂S.

Sodium to replace (as Na₂O)9.0000t/d
Saltcake (Na₂SO₄)0t/d
Caustic (NaOH)11.616t/d
Sulphur brought in by the saltcake0t/d

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 12 kg Na2O/ADt, 1000 ADt/d, half saltcake. The inputs, in the units selected above:

InputValue
Soda loss per ADt (as Na₂O)12.000 kg/t
Pulp production (air-dry)1,000.0 t/d
Share made up as saltcake (rest as NaOH)50.000 %

Applying the formula below gives:

ResultValue
Sodium to replace (as Na₂O)12.000 t/d
Saltcake (Na₂SO₄)13.750 t/d
Caustic (NaOH)7.7440 t/d
Sulphur brought in by the saltcake3.1036 t/d

Open this example in the calculator and change any input.

Formula

\(n = \frac{L_{Na_2O}P}{M_{Na_2O}}, \quad \dot m_{Na_2SO_4} = f_snM_{Na_2SO_4}, \quad \dot m_{NaOH} = 2(1 - f_s)nM_{NaOH}\)

Variables

Symbol Meaning SI unit
\(L_{Na_2O}\) Soda loss per ADt (as Na₂O) kg/kg
\(P\) Pulp production (air-dry) kg/s
\(f_s\) Share made up as saltcake (rest as NaOH) -
\(\dot m_{Na_2O}\) Sodium to replace (as Na₂O) kg/s
\(\dot m_{Na_2SO_4}\) Saltcake (Na₂SO₄) kg/s
\(\dot m_{NaOH}\) Caustic (NaOH) kg/s
\(\dot m_S\) Sulphur brought in by the saltcake kg/s

Method and standards

Sodium balance.

Where it is used

  • Liquor cycle balances.
  • Chemical purchasing.

Common mistakes

  • Mixing Na₂O and NaOH bases.
  • Ignoring sulphur added.

Assumptions and limits

  • Make-up equals losses.
  • The sulphur shown is what the saltcake brings in. Saltcake is only partly reduced in the recovery boiler, so the sulphur made available as Na₂S is less; the sodium balance is unaffected.

References

  • Smook
  • Handbook for Pulp & Paper Technologists
  • 3rd ed. (Angus Wilde, 2002)
  • ch. 10 (chemical make-up of soda losses)
  • Stoichiometry: Na₂SO₄ and 2 NaOH per Na₂O; IUPAC masses

Questions and answers

What soda loss is typical?

10–20 kg Na₂O per ADt in modern mills.

Why express as Na₂O?

It is the liquor cycle's common basis for all sodium compounds.

Why not all saltcake?

Too much sulphur raises sulfidity and TRS emissions.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.