FireCADCalc

Stock Refining: Specific Energy and Specific Edge Load

Gross and net specific refining energy (kWh/t, HP-day/ton) and specific edge load from refiner and no-load power, throughput, speed and edge length.

Pulp and paper

Inputs

Examples: 900 kW refiner, 300 kW no-load, 500 t/dLow-intensity hardwood

Results

SEL is in J/m (= W·s/m): low SEL (≈1 J/m) fibrillates, high SEL cuts fibres.

Gross specific energy43.200kWh/t
Net specific energy28.800kWh/t
Net energy, HP-day per short ton (HPD/ton)1.4599
Specific edge load (J/m)0.60000

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 900 kW refiner, 300 kW no-load, 500 t/d. The inputs, in the units selected above:

InputValue
Refiner motor power900.00 kW
No-load power300.00 kW
Pulp production (oven-dry)500.00 t/d
Rotor speed1,000.0 rpm
Cutting edge length per revolution60.000 km

Applying the formula below gives:

ResultValue
Gross specific energy43.200 kWh/t
Net specific energy28.800 kWh/t
Net energy, HP-day per short ton (HPD/ton)1.4599
Specific edge load (J/m)0.60000

Open this example in the calculator and change any input.

Formula

\(E_g = \frac{P}{\dot m_{OD}}, \quad E_n = \frac{P - P_0}{\dot m_{OD}}, \quad SEL = \frac{P - P_0}{N L_s}\)

Variables

Symbol Meaning SI unit
\(P\) Refiner motor power W
\(P_0\) No-load power W
\(\dot m_{OD}\) Pulp production (oven-dry) kg/s
\(N\) Rotor speed 1/s
\(L_s\) Cutting edge length per revolution m
\(E_g\) Gross specific energy J/kg
\(E_n\) Net specific energy J/kg
\(E_{HPD}\) Net energy, HP-day per short ton (HPD/ton) HPD/ton
\(SEL\) Specific edge load (J/m) J/m

Method and standards

Specific energy and edge load definitions.

Where it is used

  • Refiner control and plate selection.

Common mistakes

  • Using gross energy to compare refiners.
  • Forgetting the bar intersections are per revolution.

Assumptions and limits

  • Throughput as OD fibre.
  • SEL is in J/m (W·s/m) and E_HPD in HP-day per short ton; both are shown as plain numbers in every unit system.

References

  • Smook
  • Handbook for Pulp & Paper Technologists
  • 3rd ed. (Angus Wilde, 2002)
  • ch. 13.2 (refining; specific energy in kWh/t or HP-day/ton) and ch. 5 (groundwood specific energy)
  • Specific edge load: net power / (speed × cutting edge length)

Questions and answers

Why subtract no-load power?

No-load power is spent pumping and in friction; only net power works on the fibres.

What is a HP-day per ton?

The older North American unit; 1 HPD/short ton ≈ 19.7 kWh/t.

What SEL suits hardwood?

About 0.4–1 J/m; softwood 1.5–4 J/m.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.