FireCADCalc

Lime Kiln: CaO Output, Calcination Heat and Fuel

Burnt lime from lime mud, the calcination heat, and kiln fuel from a specific heat consumption per tonne of CaO, with the CO₂ released by calcination.

Pulp and paper

Inputs

Examples: 400 t/d mud at 75 %, 6.5 GJ/tEfficient kiln

Results

Calcination needs about 3.2 GJ/t CaO in theory; real kilns use 5.5–8 GJ/t because of mud water and exit gas losses.

CaO produced168.09t/d
CO₂ from calcination131.91t/d
Water evaporated from the mud65.854t/d
Calcination heat (theoretical)6.1857MW
Fuel22.412t/d

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 400 t/d mud at 75 %, 6.5 GJ/t. The inputs, in the units selected above:

InputValue
Lime mud to the kiln (dry CaCO₃)400.00 t/d
Mud dryness75.000 %
Kiln heat consumption per tonne CaO6.5000 MJ/kg
Fuel lower heating value40.000 MJ/kg

Applying the formula below gives:

ResultValue
CaO produced224.12 t/d
CO₂ from calcination175.88 t/d
Water evaporated from the mud133.33 t/d
Calcination heat (theoretical)8.2475 MW
Fuel36.419 t/d

Open this example in the calculator and change any input.

Formula

\(\dot n = \frac{\dot m_{mud}}{M_{CaCO_3}}, \quad \dot m_{CaO} = \dot n M_{CaO}, \quad \dot m_f = \frac{\dot m_{CaO} q}{LHV}\)

Variables

Symbol Meaning SI unit
\(\dot m_{mud}\) Lime mud to the kiln (dry CaCO₃) kg/s
\(d\) Mud dryness -
\(q\) Kiln heat consumption per tonne CaO J/kg
\(LHV\) Fuel lower heating value J/kg
\(\dot m_{CaO}\) CaO produced kg/s
\(\dot m_{CO_2}\) CO₂ from calcination kg/s
\(\dot m_w\) Water evaporated from the mud kg/s
\(Q_c\) Calcination heat (theoretical) W
\(\dot m_f\) Fuel kg/s

Method and standards

Calcination stoichiometry.

Where it is used

  • Kiln fuel budgets.
  • CO₂ reporting.

Common mistakes

  • Using the theoretical heat for fuel.
  • Counting mud water as CaCO₃.

Assumptions and limits

  • Pure CaCO₃ mud: inerts, residual sodium and unreacted CaO in real mud are not counted, so CaO and CO₂ are slightly overstated.
  • Fuel = CaO × q / LHV; it does not depend on the mud dryness entered, which only sets the water evaporated.

References

  • Smook
  • Handbook for Pulp & Paper Technologists
  • 3rd ed. (Angus Wilde, 2002)
  • ch. 10 (lime kiln: CaCO₃ → CaO + CO₂)
  • Heat of calcination about 178 kJ/mol CaCO₃ (standard enthalpy of reaction at 25 °C)

Questions and answers

Why is real heat use double the theory?

Water in the mud, hot exit gases, hot lime and shell losses.

Does calcination CO₂ count as fossil?

It is process CO₂ from the carbonate, reported separately from fuel CO₂.

How does mud dryness help?

Each extra percent of dryness cuts kiln fuel noticeably; modern filters reach 75–85 %. In this calculator the fuel follows the heat consumption q you enter, so use a lower q for drier mud; the water evaporated is shown for reference.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.