Worked example
Example: 500 t/d, 1.2 % to 13 %, shower 4500 t/d (DF 2.3). The inputs, in the units selected above:
| Input | Value |
|---|---|
| Pulp production (oven-dry) | 500.00 t/d |
| Shower water | 4,500.0 t/d |
| Consistency of stock entering | 1.2000 % |
| Consistency of the sheet leaving | 13.000 % |
| Vat liquor solids | 12.000 % |
| Liquor solids in the sheet leaving | 4.0000 % |
| Wash liquor solids | 0 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Liquor per kg pulp entering | 82.333 kg/kg |
| Liquor per kg pulp leaving | 6.6923 kg/kg |
| Dilution factor | 2.3077 kg/kg |
| Thickening factor | 91.872 % |
| Displacement ratio | 66.667 % |
| Overall solids removal | 97.291 % |
Open this example in the calculator and change any input.
Formula
\(DF = \frac{\dot m_{sh} - W_{out}\dot m_{OD}}{\dot m_{OD}}, \quad W = \frac{1 - C}{C}, \quad TF = \frac{W_{in} - W_{out}}{W_{in}}, \quad DR = \frac{C_v - C_s}{C_v - C_w}, \quad \eta = TF + (1 - TF)DR\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot m_{OD}\) | Pulp production (oven-dry) | kg/s |
| \(\dot m_{sh}\) | Shower water | kg/s |
| \(C_{in}\) | Consistency of stock entering | - |
| \(C_{out}\) | Consistency of the sheet leaving | - |
| \(C_v\) | Vat liquor solids | - |
| \(C_s\) | Liquor solids in the sheet leaving | - |
| \(C_w\) | Wash liquor solids | - |
| \(W_{in}\) | Liquor per kg pulp entering | kg/kg |
| \(W_{out}\) | Liquor per kg pulp leaving | kg/kg |
| \(DF\) | Dilution factor | kg/kg |
| \(TF\) | Thickening factor | - |
| \(DR\) | Displacement ratio | - |
| \(\eta\) | Overall solids removal | - |
Method and standards
Smook's washer definitions.
Where it is used
- Brown stock washer audits.
- Soda loss and evaporator load trade-offs.
Common mistakes
- Using consistency in % in W = (100 − C)/C mixed with fractions.
- Including fibre in liquor solids.
Assumptions and limits
- Liquor density 1 kg/L; solids by mass.
- The dilution factor and the displacement ratio are independent inputs here; a negative dilution factor gives a note. The sheet liquor solids must lie between the wash and vat liquor solids.
References
- Smook
- Handbook for Pulp & Paper Technologists
- 3rd ed. (Angus Wilde, 2002)
- ch. 9.3 (brown stock washing: DF, DR, TF and % efficiency = [TF + (1 − TF)DR]100)
Questions and answers
What is the dilution factor?
Wash water applied in excess of the water leaving with the pulp, per kg of oven-dry pulp.
Why is one stage not enough?
A single displacement stage rarely exceeds 80 %; three or four stages reach about 99 % removal.
What is the thickening factor?
The share of liquor removed simply by raising the consistency from vat to sheet.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.