FireCADCalc

Brown Stock Washing: Dilution Factor, Displacement Ratio, Efficiency

Dilution factor, thickening factor, displacement ratio and overall dissolved-solids removal of a brown stock washer stage, by Smook's definitions (ch. 9).

Pulp and paper

Inputs

Examples: 500 t/d, 1.2 % to 13 %, shower 4500 t/d (DF 2.3)Wash press

Results

A higher dilution factor washes better but sends more water to the evaporators; 2–3 t/t is usual.

Liquor per kg pulp entering82.333kg/kg
Liquor per kg pulp leaving6.6923kg/kg
Dilution factor2.3077kg/kg
Thickening factor91.872%
Displacement ratio66.667%
Overall solids removal97.291%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 500 t/d, 1.2 % to 13 %, shower 4500 t/d (DF 2.3). The inputs, in the units selected above:

InputValue
Pulp production (oven-dry)500.00 t/d
Shower water4,500.0 t/d
Consistency of stock entering1.2000 %
Consistency of the sheet leaving13.000 %
Vat liquor solids12.000 %
Liquor solids in the sheet leaving4.0000 %
Wash liquor solids0 %

Applying the formula below gives:

ResultValue
Liquor per kg pulp entering82.333 kg/kg
Liquor per kg pulp leaving6.6923 kg/kg
Dilution factor2.3077 kg/kg
Thickening factor91.872 %
Displacement ratio66.667 %
Overall solids removal97.291 %

Open this example in the calculator and change any input.

Formula

\(DF = \frac{\dot m_{sh} - W_{out}\dot m_{OD}}{\dot m_{OD}}, \quad W = \frac{1 - C}{C}, \quad TF = \frac{W_{in} - W_{out}}{W_{in}}, \quad DR = \frac{C_v - C_s}{C_v - C_w}, \quad \eta = TF + (1 - TF)DR\)

Variables

Symbol Meaning SI unit
\(\dot m_{OD}\) Pulp production (oven-dry) kg/s
\(\dot m_{sh}\) Shower water kg/s
\(C_{in}\) Consistency of stock entering -
\(C_{out}\) Consistency of the sheet leaving -
\(C_v\) Vat liquor solids -
\(C_s\) Liquor solids in the sheet leaving -
\(C_w\) Wash liquor solids -
\(W_{in}\) Liquor per kg pulp entering kg/kg
\(W_{out}\) Liquor per kg pulp leaving kg/kg
\(DF\) Dilution factor kg/kg
\(TF\) Thickening factor -
\(DR\) Displacement ratio -
\(\eta\) Overall solids removal -

Method and standards

Smook's washer definitions.

Where it is used

  • Brown stock washer audits.
  • Soda loss and evaporator load trade-offs.

Common mistakes

  • Using consistency in % in W = (100 − C)/C mixed with fractions.
  • Including fibre in liquor solids.

Assumptions and limits

  • Liquor density 1 kg/L; solids by mass.
  • The dilution factor and the displacement ratio are independent inputs here; a negative dilution factor gives a note. The sheet liquor solids must lie between the wash and vat liquor solids.

References

  • Smook
  • Handbook for Pulp & Paper Technologists
  • 3rd ed. (Angus Wilde, 2002)
  • ch. 9.3 (brown stock washing: DF, DR, TF and % efficiency = [TF + (1 − TF)DR]100)

Questions and answers

What is the dilution factor?

Wash water applied in excess of the water leaving with the pulp, per kg of oven-dry pulp.

Why is one stage not enough?

A single displacement stage rarely exceeds 80 %; three or four stages reach about 99 % removal.

What is the thickening factor?

The share of liquor removed simply by raising the consistency from vat to sheet.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.