FireCADCalc

Bleaching Stage: Chemical, Solution and Dilution Water

Chemical use, solution flow and dilution water of a bleaching stage from OD pulp flow, chemical charge on pulp, solution strength and the stage consistency.

Pulp and paper

Inputs

Examples: 2 % peroxide (500 g/L solution) at 10 % consistencyClO2 D1 stagePage defaults: 1 % ClO2 at 10 g/L, 12 to 10 %

On the same chemical basis as the solution strength (for example both as ClO₂, not one as active chlorine: 1 kg ClO₂ = 2.63 kg active chlorine).

Results

Chemical208.33kg/h
Chemical solution347.22L/min
Dilution water after the solution13.889t/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 2 % peroxide (500 g/L solution) at 10 % consistency. The inputs, in the units selected above:

InputValue
Pulp production (oven-dry)500.00 t/d
Chemical charge on OD pulp2.0000 %
Chemical solution strength500.00 g/L
Consistency of pulp entering the mixer12.000 %
Stage consistency10.000 %

Applying the formula below gives:

ResultValue
Chemical416.67 kg/h
Chemical solution13.889 L/min
Dilution water after the solution33.889 t/h

Open this example in the calculator and change any input.

Formula

\(\dot m_c = c\,\dot m_{OD}, \quad \dot V_s = \frac{\dot m_c}{s}, \quad \dot m_{dw} = \dot m_{OD}\left(\frac{1}{C_{st}} - \frac{1}{C_{in}}\right) - \rho_w\dot V_s\)

Variables

Symbol Meaning SI unit
\(\dot m_{OD}\) Pulp production (oven-dry) kg/s
\(c\) Chemical charge on OD pulp -
\(s\) Chemical solution strength kg/m³
\(C_{in}\) Consistency of pulp entering the mixer -
\(C_{st}\) Stage consistency -
\(\dot m_c\) Chemical kg/s
\(\dot V_s\) Chemical solution m³/s
\(\dot m_{dw}\) Dilution water after the solution kg/s

Method and standards

Fibre and water balances.

Where it is used

  • Bleach plant operation.

Common mistakes

  • Charging on air-dry pulp.
  • Forgetting the solution water.

Assumptions and limits

  • Solution density 1 kg/L.
  • The charge and the solution strength must be on the same chemical basis (both as ClO₂, or both as active chlorine; they differ by 2.63 times).
  • When the solution alone over-dilutes, or the stage is thicker than the incoming pulp, no dilution water is shown and a note explains why.

References

  • Smook
  • Handbook for Pulp & Paper Technologists
  • 3rd ed. (Angus Wilde, 2002)
  • ch. 11 (bleaching: charges on OD pulp at a stage consistency)

Questions and answers

Why charge on OD pulp?

Chemical demand scales with fibre, not with water.

Why medium consistency?

10–12 % stages use less steam and chemical and smaller towers than low consistency.

Does the solution dilute the pulp?

Yes; its volume is counted before adding dilution water.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.