FireCADCalc

Mill Trashplate Setting (Hugot)

Trashplate clearances at the toe, middle, heel and tip from the feed opening, Hugot's proportions (Table 13.9), the empty settings and the trashplate angle rule.

Sugar mill and cogeneration

Inputs

Examples: Hugot example E 79, E0 61Smaller mill

Results

Hugot's example: E_A = 79 mm and E₀ = 61 mm give about A 118, M 138, Z 150, T 63 mm working and A₀ 96, M₀ 115, Z₀ 128 mm empty.

Clearance at the toe (feed side), working82.500mm
Clearance at the middle, working96.250mm
Clearance at the heel, working104.50mm
Clearance at the tip (delivery side)44.000mm
Toe clearance, empty70.500mm
Middle clearance, empty83.750mm
Heel clearance, empty92.500mm
Trashplate angle α/612.000°
Offset 0.00145 D α (α in degrees)79.553mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Hugot example E 79, E0 61. The inputs, in the units selected above:

InputValue
Working feed opening79.000 mm
Empty feed opening61.000 mm
Top roller angle70.000 °
Roller diameter0.91400 m

Applying the formula below gives:

ResultValue
Clearance at the toe (feed side), working118.50 mm
Clearance at the middle, working138.25 mm
Clearance at the heel, working150.10 mm
Clearance at the tip (delivery side)63.200 mm
Toe clearance, empty96.900 mm
Middle clearance, empty115.75 mm
Heel clearance, empty128.50 mm
Trashplate angle α/611.667 °
Offset 0.00145 D α (α in degrees)92.771 mm

Open this example in the calculator and change any input.

Formula

\(A = 1.50E_A,\ M = 1.75E_A,\ Z = 1.90E_A,\ T = 0.80E_A\)

\(A_0 = A - 1.2\Delta E,\ M_0 = M - 1.25\Delta E,\ Z_0 = Z - 1.2\Delta E,\ \beta = \frac{\alpha}{6},\ MB = 0.00145\,D\,\alpha\)

Variables

Symbol Meaning SI unit
\(E_A\) Working feed opening m
\(E_0\) Empty feed opening m
\(\alpha\) Top roller angle rad
\(D\) Roller diameter m
\(A\) Clearance at the toe (feed side), working m
\(M\) Clearance at the middle, working m
\(Z\) Clearance at the heel, working m
\(T\) Clearance at the tip (delivery side) m
\(A_0\) Toe clearance, empty m
\(M_0\) Middle clearance, empty m
\(Z_0\) Heel clearance, empty m
\(\beta\) Trashplate angle α/6 rad
\(MB\) Offset 0.00145 D α (α in degrees) m

Method and standards

Hugot's proportions per 100 of feed opening.

Where it is used

  • Setting trashplates at the start of season.
  • Diagnosing trashplate chokes.

Common mistakes

  • Using the delivery opening as the base.
  • Forgetting to correct for the empty position.

Assumptions and limits

  • Hugot's proportions for normal 3-roller mills.
  • In MB = 0.00145 D α the roller diameter D is in metres and α in degrees, giving MB in metres (93 mm for the default).
  • Empty clearances that would come out negative are rejected.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 13
  • eqns 13.11–13.12 and Table 13.9
  • pp. 217–222

Questions and answers

Why is the heel clearance largest?

The blanket swells on the trashplate after leaving the feed nip; the passage widens towards the delivery roller to avoid choking.

What are A, M, Z and T?

Hugot's clearances between the trashplate and the top roller at the toe, middle, heel and the tip at the delivery roller.

Why are empty clearances smaller?

With the mill stopped the top roller sits lower; the feed-side clearances drop about 1.2 times the change of the feed opening.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.