Worked example
Example: 1067 x 2134, 380 mm rams at 300 kg/cm2. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Ram (piston) diameter | 380.00 mm |
| Number of rams | 2.0000 - |
| Oil pressure (gauge) | 300.00 kgf/cm² |
| Packing friction as a share of the load | 4.0000 % |
| Roller length | 2.1340 m |
| Roller diameter | 1.0670 m |
| Journal diameter | 560.00 mm |
| Journal (bearing) length | 600.00 mm |
Applying the formula below gives:
| Result | Value |
|---|---|
| Total hydraulic load on the top roller | 653.25 tf |
| Specific hydraulic pressure F/(LD/10) | 28.689 t/dm² |
| Journal bearing pressure (half the load / journal area) | 97.210 kgf/cm² |
| Hugot's mean load 250 L D tonnes (25 t/dm²) | 569.24 tf |
Open this example in the calculator and change any input.
Formula
\(F = n_r\,p_o\,\frac{\pi d_r^2}{4}(1 - \varphi), \quad p = \frac{F}{L D / 10}, \quad p_j = \frac{F/2}{d_j\,l_j}, \quad F_n = 250\,L D\ \mathrm{t}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(d_r\) | Ram (piston) diameter | m |
| \(n_r\) | Number of rams | - |
| \(p_o\) | Oil pressure (gauge) | Pa |
| \(\varphi\) | Packing friction as a share of the load | - |
| \(L\) | Roller length | m |
| \(D\) | Roller diameter | m |
| \(d_j\) | Journal diameter | m |
| \(l_j\) | Journal (bearing) length | m |
| \(F\) | Total hydraulic load on the top roller | N |
| \(p\) | Specific hydraulic pressure F/(LD/10) | Pa |
| \(p_j\) | Journal bearing pressure (load of one ram / journal area) | Pa |
| \(F_n\) | Hugot's mean load 250 L D tonnes (25 t/dm²) | N |
Method and standards
Ram force less packing friction (Hugot eqns 10.1–10.2) over the roller and journal areas.
Where it is used
- Setting and checking mill hydraulics.
- Comparing pressure between mills.
Common mistakes
- Entering the accumulator gas pressure instead of oil pressure.
- Using the circumference instead of L × D.
Assumptions and limits
- Static load; roller floating freely.
- The top roller rests on two journals, so each carries half the total load whatever the number of rams. A note appears above Hugot's 110 kg/cm².
References
- Hugot
- Handbook of Cane Sugar Engineering
- 3rd ed. (Elsevier, 1986)
- ch. 10
- eqns 10.1–10.6
- 10.82–10.83 and journal pressures
- pp. 117–125 and 172–174
Questions and answers
What is s.h.p.?
Specific hydraulic pressure: the total hydraulic load on the top roller divided by one tenth of the roller's projected area, L × D/10, quoted in t/dm² (Hugot's convention, which is why his normal load 250 L D tonnes, with L and D in metres, equals 25 t/dm²).
Normal values?
Hugot reports 12–40 t/dm², mostly 20–25; the crusher about half the first mill; the last mill 28–30.
Why subtract packing friction?
The ram packings hold back 3–5 % of the oil force before it reaches the journals.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.