FireCADCalc

Mill Control Basic Equation and Dilution

Bagasse % cane and fibre % cane from the basic mill balance with yard and evaporation losses (Hugot eqns 21.12, 21.15), and dilution against imbibition (Shannon).

Sugar mill and cogeneration

Inputs

Examples: Hugot dilution exampleHot imbibition

Hugot: 0.5–1 %.
Hugot: 0.5–1 % cold imbibition, 1–2 % hot.

Results

Shannon: dilution/imbibition between 0.95 and 1.05 is normal; below, the imbibition figure is too high, above, too low. Hugot's example: 19.16 and 14.98 brix with 29.06 % imbibition give k = 0.96.

Bagasse % cane, uncorrected 100 + W − Q28.000%
Bagasse % cane, corrected for losses25.500%
Fibre % cane, uncorrected14.000%
Fibre % cane, corrected12.750%
Dilution % primary juice 100(B₁ − B_m)/B_m31.579%
Dilution / imbibition (Shannon)0.98684

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Hugot dilution example. The inputs, in the units selected above:

InputValue
Imbibition water % cane29.060 %
Mixed juice % cane102.00 %
Cane weight lost in the yard % cane0.75000 %
Juice evaporated at the mills % cane0.75000 %
Fibre % bagasse48.000 %
Brix of primary juice19.160 %
Brix of mixed juice14.980 %

Applying the formula below gives:

ResultValue
Bagasse % cane, uncorrected 100 + W − Q27.060 %
Bagasse % cane, corrected for losses25.560 %
Fibre % cane, uncorrected12.989 %
Fibre % cane, corrected12.269 %
Dilution % primary juice 100(B₁ − B_m)/B_m27.904 %
Dilution / imbibition (Shannon)0.96022

Open this example in the calculator and change any input.

Formula

\(B = 100 + W - Q, \quad B_c = B - (\gamma + \zeta), \quad f = f'\frac{B}{100}, \quad f_c = f'\frac{B_c}{100}, \quad D = \frac{100(B_1 - B_m)}{B_m}, \quad k = \frac{D}{W}\)

Variables

Symbol Meaning SI unit
\(W\) Imbibition water % cane -
\(Q\) Mixed juice % cane -
\(\gamma\) Cane weight lost in the yard % cane -
\(\zeta\) Juice evaporated at the mills % cane -
\(f'\) Fibre % bagasse -
\(B_1\) Brix of primary juice -
\(B_m\) Brix of mixed juice -
\(B\) Bagasse % cane, uncorrected 100 + W − Q -
\(B_c\) Bagasse % cane, corrected for losses -
\(f\) Fibre % cane, uncorrected -
\(f_c\) Fibre % cane, corrected -
\(D\) Dilution % primary juice 100(B₁ − B_m)/B_m -
\(k\) Dilution / imbibition (Shannon) -

Method and standards

Hugot's basic equation for mills and Shannon's check.

Where it is used

  • Daily chemical control.
  • Checking imbibition and juice scales.

Common mistakes

  • Using gross mixed juice.
  • Taking fibre % bagasse from a wet sample.

Assumptions and limits

  • All quantities per 100 cane weighed.
  • A note flags a mixed juice brix at or above the primary juice brix, and a Shannon ratio outside 0.95–1.05.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 21
  • eqns 21.7–21.15 and dilution (Shannon)
  • pp. 333–341

Questions and answers

Why correct for losses?

Cane dries in the yard and juice evaporates at the mills; ignoring this makes the computed bagasse 3–10 % too high.

Imbibition or dilution?

Imbibition is water added at the mills; dilution is the part of it that reaches the mixed juice. The difference stays in the bagasse.

Is the uncorrected figure wrong?

It is the official figure in most control schemes; Hugot asks that its limits be known.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.