FireCADCalc

Pulp and Paper Mill Water and Effluent KPIs

Specific water intake, effluent volume and BOD, COD and TSS loads per tonne of product from mill flows and effluent concentrations (Smook ch. 25–26).

Pulp and paper

Inputs

Examples: 1000 t/d millClosed board mill

State the basis (air-dry tonnes ADt, oven-dry ODt or net saleable) and use the same basis as the benchmark or permit.

Results

Water intake per tonne10.0000m³/t
Effluent per tonne7.5000m³/t
BOD load per tonne0.15000kg/t
COD load per tonne0.90000kg/t
TSS load per tonne0.22500kg/t

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1000 t/d mill. The inputs, in the units selected above:

InputValue
Production1,000.0 t/d
Fresh water intake1,250.0 m³/h
Effluent flow1,041.7 m³/h
Effluent BOD30.000 mg/L
Effluent COD150.00 mg/L
Effluent TSS40.000 mg/L

Applying the formula below gives:

ResultValue
Water intake per tonne30.000 m³/t
Effluent per tonne25.000 m³/t
BOD load per tonne0.75000 kg/t
COD load per tonne3.7500 kg/t
TSS load per tonne1.0000 kg/t

Open this example in the calculator and change any input.

Formula

\(w = \frac{\dot V_{in}}{P}, \quad \frac{BOD}{t} = \frac{\dot V_e c_{BOD}}{P}\)

Variables

Symbol Meaning SI unit
\(P\) Production kg/s
\(\dot V_{in}\) Fresh water intake m³/s
\(\dot V_{e}\) Effluent flow m³/s
\(c_{BOD}\) Effluent BOD kg/m³
\(c_{COD}\) Effluent COD kg/m³
\(c_{TSS}\) Effluent TSS kg/m³
\(w\) Water intake per tonne m³/kg
\(e\) Effluent per tonne m³/kg
\(BOD/t\) BOD load per tonne kg/kg
\(COD/t\) COD load per tonne kg/kg
\(TSS/t\) TSS load per tonne kg/kg

Method and standards

Load definitions.

Where it is used

  • Environmental reporting.
  • Water reduction programmes.

Common mistakes

  • Mixing ADt and tonnes of paper.
  • Using intake instead of effluent for loads.

Assumptions and limits

  • Daily averages.
  • The per-tonne figures are on whatever production basis is entered (air-dry tonnes ADt, oven-dry ODt or net saleable product); compare them only with benchmarks on the same basis.

References

  • Smook
  • Handbook for Pulp & Paper Technologists
  • 3rd ed. (Angus Wilde, 2002)
  • ch. 25 (mill water supply) and ch. 26 (effluent: BOD, COD and suspended solids)

Questions and answers

What water use is good?

Modern integrated mills use 10–30 m³/t; older mills over 100 m³/t.

Why per tonne?

Permits and benchmarks compare mills by load per tonne of product.

Is BOD in mg/L the same as g/m³?

Yes, so flow in m³ times mg/L gives grams.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.