FireCADCalc

Kraft Cook: Alkali Charge and Liquor-to-Wood Ratio

White and black liquor volumes and liquor-to-wood ratio for a kraft cook from wood, chip moisture, alkali charge on wood and liquor strength (Smook ch. 7).

Pulp and paper

Inputs

Examples: 50 t OD wood, 15 % EA, 4 m3/tHardwood 13 %

Volume ratio: m³ of total liquor per OD tonne of wood (= L/kg). For a mass ratio in t/t, divide it by the liquor density in t/m³ first.

Results

Effective alkali required5,200.0kg
White liquor volume47.273m³
Water in the chips26.667m³
Black liquor (or water) to make up the ratio66.061m³

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50 t OD wood, 15 % EA, 4 m3/t. The inputs, in the units selected above:

InputValue
Wood charged (oven-dry)50,000 kg
Chip moisture (wet basis)45.000 %
Effective alkali charge on OD wood (as Na₂O)15.000 %
White liquor effective alkali (as Na₂O)100.00 g/L
Target liquor-to-wood ratio4.0000 -

Applying the formula below gives:

ResultValue
Effective alkali required7,500.0 kg
White liquor volume75.000 m³
Water in the chips40.909 m³
Black liquor (or water) to make up the ratio84.091 m³

Open this example in the calculator and change any input.

Formula

\(EA = EA\% \times W, \quad V_{WL} = \frac{EA}{c_{WL}}, \quad V_{chip} = \frac{W m_c}{(1 - m_c)\rho_w}, \quad V_{BL} = (L/W)\,W - V_{WL} - V_{chip}\)

Variables

Symbol Meaning SI unit
\(W\) Wood charged (oven-dry) kg
\(m_c\) Chip moisture (wet basis) -
\(EA\%\) Effective alkali charge on OD wood (as Na₂O) -
\(c_{WL}\) White liquor effective alkali (as Na₂O) kg/m³
\(L/W\) Target liquor-to-wood ratio -
\(EA\) Effective alkali required kg
\(V_{WL}\) White liquor volume m³
\(V_{chip}\) Water in the chips m³
\(V_{BL}\) Black liquor (or water) to make up the ratio m³

Method and standards

Mass balance of the digester charge.

Where it is used

  • Batch digester charging.
  • Continuous digester liquor ratios.

Common mistakes

  • Basing the charge on wet chips.
  • Mixing EA and AA.

Assumptions and limits

  • Water density 1 000 kg/m³; liquor volumes additive.
  • The liquor-to-wood ratio is a volume ratio (m³ per OD tonne). A ratio specified by mass (t/t) must be converted with the liquor density, or the black liquor make-up is off by 10–20 %.

References

  • Smook
  • Handbook for Pulp & Paper Technologists
  • 3rd ed. (Angus Wilde, 2002)
  • ch. 7 (kraft pulping: alkali charge on wood and liquor-to-wood ratio)

Questions and answers

Why charge on oven-dry wood?

Alkali consumption depends on the wood substance, not its water.

What charge is typical?

13–18 % effective alkali as Na₂O on OD wood for softwood bleachable grades.

Why add black liquor?

To reach the liquor-to-wood ratio needed to cover the chips without diluting the alkali with fresh water.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.