FireCADCalc

Headbox Jet Velocity, Flow and Jet-to-Wire Ratio

Slice jet velocity from headbox head by Bernoulli (v = √2gh), jet flow with a contraction coefficient, and the jet-to-wire ratio with rush or drag.

Pulp and paper

Inputs

Examples: 18 m head, 12 mm sliceSlow board machine

Results

A jet-to-wire ratio a little off 1 (rush or drag) sets fibre orientation and formation; it is a key tuning variable.

Jet velocity420.14m/min
Jet-to-wire ratio1.0504
Rush (+) or drag (−)20.142m/min
Headbox flow2,205.7m³/h
Fibre in the jet22.057t/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 18 m head, 12 mm slice. The inputs, in the units selected above:

InputValue
Total head at the slice (as stock)18.000 m
Slice opening12.000 mm
Jet contraction coefficient65.000 %
Slice width9.0000 m
Wire speed1,200.0 m/min
Headbox consistency0.60000 %

Applying the formula below gives:

ResultValue
Jet velocity1,127.4 m/min
Jet-to-wire ratio0.93947
Rush (+) or drag (−)-72.639 m/min
Headbox flow4,748.4 m³/h
Fibre in the jet28.491 t/h

Open this example in the calculator and change any input.

Formula

\(v_j = \sqrt{2gh}, \quad Q = v_j\,b\,C_c\,W, \quad \frac{v_j}{v_w}\)

Variables

Symbol Meaning SI unit
\(h\) Total head at the slice (as stock) m
\(b\) Slice opening m
\(C_c\) Jet contraction coefficient -
\(W\) Slice width m
\(v_w\) Wire speed m/s
\(C\) Headbox consistency -
\(v_j\) Jet velocity m/s
\(v_j/v_w\) Jet-to-wire ratio -
\(v_j - v_w\) Rush (+) or drag (−) m/s
\(Q\) Headbox flow m³/s
\(\dot m_{OD}\) Fibre in the jet kg/s

Method and standards

Bernoulli jet as given by Smook.

Where it is used

  • Headbox setting and grade changes.

Common mistakes

  • Using gauge pressure in kPa as head without conversion.
  • Ignoring jet contraction.

Assumptions and limits

  • No losses in the slice; stock density about 1 000 kg/m³. Real jets run about 1–3 % slower than √(2gh) because of a velocity coefficient that is not applied here; since the jet-to-wire ratio is tuned within a few per cent of 1, calibrate against a measured jet speed.

References

  • Smook
  • Handbook for Pulp & Paper Technologists
  • 3rd ed. (Angus Wilde, 2002)
  • ch. 16.3 (headbox: jet speed from Bernoulli, v = √(2gh); jet contraction)

Questions and answers

Why total head?

Pond level plus air-cushion pressure (as stock height) drives the jet.

What is jet contraction?

The jet is thinner than the slice opening; Smook notes it must be allowed for when computing flow.

What head gives 1,200 m/min?

About 20 m of stock.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.