FireCADCalc

Boiler Size for a KLPD Distillery

Steam demand and boiler rating for a distillery from its capacity and the specific steam of distillation, dehydration, evaporation and other users, with a margin.

Distillery and ethanolBoiler

Inputs

Examples: 100 KLPD ZLD60 KLPD, no MEE

Results

Check steam pressure levels too: multi-pressure distillation and MEE need different pressures.

Total specific steam2.9000kg/L
Average steam demand7.2500t/h
Boiler rating with margin7.9750t/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 100 KLPD ZLD. The inputs, in the units selected above:

InputValue
Plant capacity (absolute alcohol)100.00 kL/d
Distillation steam2.3000 kg/L
Dehydration steam0.40000 kg/L
Spent wash evaporation steam2.0000 kg/L
Other users (liquefaction, CIP, tracing)0.30000 kg/L
Design margin15.000 %

Applying the formula below gives:

ResultValue
Total specific steam5.0000 kg/L
Average steam demand20.833 t/h
Boiler rating with margin23.958 t/h

Open this example in the calculator and change any input.

Formula

\(s_t = s_d + s_h + s_e + s_o, \quad \dot m_b = \dot V_e s_t (1 + k)\)

Variables

Symbol Meaning SI unit
\(\dot V_e\) Plant capacity (absolute alcohol) m³/s
\(s_d\) Distillation steam kg/m³
\(s_h\) Dehydration steam kg/m³
\(s_e\) Spent wash evaporation steam kg/m³
\(s_o\) Other users (liquefaction, CIP, tracing) kg/m³
\(k\) Design margin -
\(s_t\) Total specific steam kg/m³
\(\dot m_s\) Average steam demand kg/s
\(\dot m_b\) Boiler rating with margin kg/s

Method and standards

Steam balance.

Where it is used

  • New distillery and expansion boilers.
  • FireCAD boiler enquiries.

Common mistakes

  • Bulk litres used.

Assumptions and limits

  • Average steady load.
  • Specific steam figures are by mass with no pressure or enthalpy basis; the boiler rating in t/h holds only at the steam conditions those figures assume. A boiler at higher pressure feeding the process through a PRDS and desuperheater delivers a different mass.
  • The default specific steam figures (2.3 + 0.4 + 2.0 + 0.3 = 5.0 kg/L) are starting values without a particular source; use your plant's or the supplier's figures.
  • Specific steam is entered and shown in kg/L in every unit system.

References

  • Steam balance on specific consumptions (kg per litre of alcohol)

Questions and answers

How big a boiler for 100 KLPD?

With the defaults, about 21 t/h average and 24 t/h with margin; your specific steam decides.

Biggest steam user?

Distillation, then spent wash evaporation for ZLD plants.

Turbine?

A back-pressure turbine between boiler and process makes the plant's power from the same steam.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.