FireCADCalc

CO₂ Scrubber Ethanol Recovery (Kremser)

Fraction of ethanol recovered from fermenter CO₂ by a water scrubber with N theoretical stages, by Kremser with the infinite-dilution K-value of ethanol in water.

Distillery and ethanolIAPWS-IF97 (water and steam)

Inputs

Examples: 20 °C water, 0.5 kg/kg, 4 stagesChilled 10 °C, 0.3 kg/kg, 6 stages

Results

Return the scrubber water to the fermenter or the beer well so the ethanol is distilled.

The infinite-dilution activity coefficient comes from Wilson energies fitted near the boiling point and is extrapolated to scrubber temperatures; treat the recovery as an estimate.

Equilibrium slope y/x at infinite dilution0.52970
Absorption factor L/(mG)2.3059
Ethanol recovered97.966%
Ethanol in the gas leaving0.010171%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 20 °C water, 0.5 kg/kg, 4 stages. The inputs, in the units selected above:

InputValue
Scrubber water temperature20.000 °C
Scrubber pressure (absolute)101.33 kPa
Water per kg of CO₂0.50000 kg/kg
Theoretical stages4.0000 -
Ethanol in the gas entering0.50000 %

Applying the formula below gives:

ResultValue
Equilibrium slope y/x at infinite dilution0.52970
Absorption factor L/(mG)2.3059
Ethanol recovered97.966 %
Ethanol in the gas leaving0.010171 %

Open this example in the calculator and change any input.

Formula

\(m = \frac{\gamma_1^\infty p_1^s(T)}{P}, \quad A = \frac{L}{mG}, \quad \phi = \frac{A^{N+1} - A}{A^{N+1} - 1}\)

Variables

Symbol Meaning SI unit
\(T\) Scrubber water temperature K
\(P\) Scrubber pressure (absolute) Pa
\(\dot m_w/\dot m_{CO_2}\) Water per kg of CO₂ kg/kg
\(N\) Theoretical stages -
\(y_{in}\) Ethanol in the gas entering -
\(m\) Equilibrium slope y/x at infinite dilution -
\(A\) Absorption factor L/(mG) -
\(\phi\) Ethanol recovered -
\(y_{out}\) Ethanol in the gas leaving -

Method and standards

Kremser recovery with the Wilson infinite-dilution activity coefficient.

Where it is used

  • Scrubber sizing for fuel and potable ethanol plants.

Common mistakes

  • Using Raoult's law (γ = 1).
  • Mixing mass and molar L/G.

Assumptions and limits

  • Dilute; isothermal; fresh water entering; Wilson model extrapolated below 78 °C.
  • The Wilson energies were fitted to boiling data at about 1 atm and are taken as independent of temperature, so the infinite-dilution activity coefficient at 5–40 °C is an extrapolation and has not been compared with measured values. A higher coefficient gives a larger m and a lower recovery.

References

  • Ethanol–water VLE at about 1 atm: Wilson equation (Perry's Chemical Engineers' Handbook, 9th ed., sec. 4) with energies 399 and 933 cal/mol fitted to FireCAD ethanol–water x–y–T data at 101.325 kPa; ethanol vapour pressure Perry's 9th ed. Table 2-8; water IAPWS-IF97
  • Kremser equation for absorbers (Perry's 9th ed. sec. 13)

Questions and answers

Why does cold water help?

Ethanol's vapour pressure falls with temperature, so m falls and the absorption factor rises.

What absorption factor is needed?

About 2 with four stages recovers roughly 98 %.

Why infinite dilution?

Scrubber liquor stays below about 1 % ethanol, where y/x is constant.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.