FireCADCalc

Grain Mash Cooking: Jet Cooker Steam and Flash

Direct steam to heat grain slurry in a jet cooker (IF97), vapour flashed to liquefaction temperature, liquefaction volume and α-amylase (Alcohol Textbook ch. 2).

Distillery and ethanolIAPWS-IF97 (water and steam)Boiler

Inputs

Examples: 20 t/h corn, 31 % solids, jet 120 °CU-tube at 140 °C

Alcohol Textbook ch. 2: modern systems run 29–33 % solids.
Starting value with no particular source; use a measured figure for your grain if you have one.
Alcohol Textbook: 120 °C (columnar), 120–140 °C (U-tube).
80–90 °C.
At least 30 min, preferably 60.
0.04–0.08 % w/w cereal for high-temperature α-amylase.

Results

The flash vapour can heat the incoming slurry; then the net steam is less. Backset and recycled water must be counted in the slurry.

Slurry64.516t/h
Slurry specific heat3.3694kJ/(kg·K)
Cooking steam5,759.6kg/h
Steam per tonne grain287.98kg/t
Vapour flashed to liquefaction temperature3,610.5kg/h
Liquefaction tank working volume60.605m³
α-amylase12.000kg/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 20 t/h corn, 31 % solids, jet 120 °C. The inputs, in the units selected above:

InputValue
Grain (meal) to the slurry20.000 t/h
Grain share of the slurry31.000 %
Specific heat of the grain solids1.5500 kJ/(kg·K)
Slurry temperature60.000 °C
Jet cooker temperature120.00 °C
Liquefaction (flash) temperature85.000 °C
Cooking steam pressure (absolute)8.0000 bar
Liquefaction residence60.000 min
Mash density1,100.0 kg/m³
α-amylase dose (w/w grain)0.060000 %

Applying the formula below gives:

ResultValue
Slurry64.516 t/h
Slurry specific heat3.3694 kJ/(kg·K)
Cooking steam5,759.6 kg/h
Steam per tonne grain287.98 kg/t
Vapour flashed to liquefaction temperature3,610.5 kg/h
Liquefaction tank working volume60.605 m³
α-amylase12.000 kg/h

Open this example in the calculator and change any input.

Formula

\(M = \frac{G}{x}, \quad c = xc_s + (1 - x)c_w, \quad \dot m_s = \frac{Mc(T_j - T_0)}{h_g(p_s) - h_f(T_j)}, \quad \dot m_f = \frac{(M + \dot m_s)c(T_j - T_f)}{h_{fg}(T_f)}\)

Variables

Symbol Meaning SI unit
\(G\) Grain (meal) to the slurry kg/s
\(x\) Grain share of the slurry -
\(c_s\) Specific heat of the grain solids J/(kg·K)
\(T_0\) Slurry temperature K
\(T_j\) Jet cooker temperature K
\(T_f\) Liquefaction (flash) temperature K
\(p_s\) Cooking steam pressure (absolute) Pa
\(t_r\) Liquefaction residence s
\(\rho_m\) Mash density kg/m³
\(e\) α-amylase dose (w/w grain) -
\(M\) Slurry kg/s
\(c\) Slurry specific heat J/(kg·K)
\(\dot m_s\) Cooking steam kg/s
\(\dot m_s/G\) Steam per tonne grain kg/kg
\(\dot m_f\) Vapour flashed to liquefaction temperature kg/s
\(V\) Liquefaction tank working volume m³
\(\dot m_E\) α-amylase kg/s
\(c_w\) Specific heat of water, 4.1868 kJ/(kg·K) J/(kg·K)
\(h_g, h_f, h_{fg}\) Saturated steam, saturated liquid and latent enthalpies (IAPWS-IF97) J/kg

Method and standards

Heat balance for direct steam injection and adiabatic flash.

Where it is used

  • Cooking system design.
  • Steam budgets for grain distilleries.

Common mistakes

  • Leaving out backset in the slurry.
  • Using indirect heating figures for jet cookers.

Assumptions and limits

  • Steam condenses fully in the mash; no heat loss.
  • c_w, the specific heat of water, is taken as 4.1868 kJ/(kg·K); the default c_s of 1.55 kJ/(kg·K) is a starting value without a particular source.
  • The supply steam is taken as dry saturated at p_s; superheated or wet steam is not handled.

References

  • Jacques
  • Lyons and Kelsall (eds.)
  • The Alcohol Textbook
  • 4th ed. (Nottingham University Press, 2003)
  • ch. 2 (Kelsall and Lyons)
  • cooking systems
  • Steam and water enthalpies from IAPWS-IF97

Questions and answers

Why a jet cooker?

Steam injected directly heats the mash instantly to 120–140 °C, gelatinising starch so enzymes can act.

Why flash after the jet?

Dropping to 80–90 °C cools the mash for liquefaction and gives vapour that can preheat the slurry.

Why does solids content matter?

Thicker slurries need less steam per tonne of grain and give stronger beer, but are harder to pump.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.