FireCADCalc

Wire Drawing: Ideal Draw Stress, Force and Maximum Reduction

Ideal drawing stress and force for wire or bar from the area reduction and mean flow stress, and the theoretical maximum reduction per pass.

Inputs

Examples: 6 to 5 mm steelCopper 3 to 2.5 mm

Results

Area reduction30.556%
Ideal draw stress σ̄ ln(A₀/A_f)145.86MPa
Draw force with efficiency4.0913kN
Ideal maximum reduction, frictionless (1 − 1/e)63.212%
Maximum reduction at this efficiency (1 − e^{−η})50.341%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 6 to 5 mm steel. The inputs, in the units selected above:

InputValue
Entry diameter6.0000 mm
Exit diameter5.0000 mm
Mean flow stress400.00 MPa
Process efficiency (friction and redundant work)70.000 %

Applying the formula below gives:

ResultValue
Area reduction30.556 %
Ideal draw stress σ̄ ln(A₀/A_f)145.86 MPa
Draw force with efficiency4.0913 kN
Ideal maximum reduction, frictionless (1 − 1/e)63.212 %
Maximum reduction at this efficiency (1 − e^{−η})50.341 %

Open this example in the calculator and change any input.

Formula

\(\sigma_d = \bar\sigma\ln\frac{A_0}{A_f}, \quad F = \frac{\sigma_d A_f}{\eta}, \quad r_{max} = 1 - e^{-1}, \quad r_{max,\eta} = 1 - e^{-\eta}\)

Variables

Symbol Meaning SI unit
\(d_0\) Entry diameter m
\(d_f\) Exit diameter m
\(\bar\sigma\) Mean flow stress Pa
\(\eta\) Process efficiency (friction and redundant work) -
\(r\) Area reduction -
\(\sigma_d\) Ideal draw stress σ̄ ln(A₀/A_f) Pa
\(F\) Draw force with efficiency N
\(r_{max}\) Ideal maximum reduction, frictionless (1 − 1/e) -
\(r_{max,\eta}\) Maximum reduction at this efficiency (1 − e^{−η}) -

Method and standards

Ideal work.

Where it is used

  • Wire and bar drawing.
  • Examinations.

Common mistakes

  • Diameter ratio for area ratio.
  • Ignoring efficiency.

Assumptions and limits

  • The breakage check compares the actual draw stress σ_d/η with the mean flow stress σ̄; work-hardened wire leaves the die with a higher flow stress, so the check is conservative.

  • r_max = 63.2 % is the frictionless limit. With the efficiency η the limit is 1 − e^(−η) (50 % at η = 0.7); practical passes are smaller still (about 30–45 %) for die life and safety.

  • Uniform deformation.

References

  • Ideal work: σ_d = σ̄ ln(A₀/A_f); maximum reduction when σ_d = σ̄
  • r = 1 − 1/e (Kalpakjian; Groover)

Questions and answers

6 to 5 mm at 400 MPa, 70 % efficient?

Ideal stress 146 MPa; force about 4.1 kN.

Why a maximum reduction?

The pulled wire cannot carry more stress than its own flow stress.

Real limit?

Friction and redundant work lower it to about 30–45 % per pass.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.