Worked example
Example: Housing and three parts. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Dimension 1: direction (+1 adds, −1 subtracts, 0 unused) | +1: adds to the gap |
| Dimension 1: nominal | 100.00 mm |
| Dimension 1: ± tolerance | 0.10000 mm |
| Dimension 2: direction (+1 adds, −1 subtracts, 0 unused) | −1: subtracts from the gap |
| Dimension 2: nominal | 40.000 mm |
| Dimension 2: ± tolerance | 0.050000 mm |
| Dimension 3: direction (+1 adds, −1 subtracts, 0 unused) | −1: subtracts from the gap |
| Dimension 3: nominal | 30.000 mm |
| Dimension 3: ± tolerance | 0.050000 mm |
| Dimension 4: direction (+1 adds, −1 subtracts, 0 unused) | −1: subtracts from the gap |
| Dimension 4: nominal | 29.500 mm |
| Dimension 4: ± tolerance | 0.050000 mm |
| Dimension 5: direction (+1 adds, −1 subtracts, 0 unused) | 0: not used |
| Dimension 5: nominal | 0 mm |
| Dimension 5: ± tolerance | 0 mm |
| Dimension 6: direction (+1 adds, −1 subtracts, 0 unused) | 0: not used |
| Dimension 6: nominal | 0 mm |
| Dimension 6: ± tolerance | 0 mm |
Applying the formula below gives:
| Result | Value |
|---|---|
| Nominal gap | 0.50000 mm |
| Worst-case variation | 0.25000 mm |
| RSS variation | 0.13229 mm |
| Worst-case minimum gap | 0.25000 mm |
| Worst-case maximum gap | 0.75000 mm |
| Statistical (RSS) minimum gap | 0.36771 mm |
| Statistical (RSS) maximum gap | 0.63229 mm |
Open this example in the calculator and change any input.
Formula
\(G = \sum s_i d_i, \quad t_{WC} = \sum t_i, \quad t_{RSS} = \sqrt{\sum t_i^2}, \quad G_{min,max} = G \mp t_{WC}, \quad G_{min,max,RSS} = G \mp t_{RSS}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(s_{1}\) | Dimension 1: direction (+1 adds, −1 subtracts, 0 unused) | - |
| \(d_{1}\) | Dimension 1: nominal | m |
| \(t_{1}\) | Dimension 1: ± tolerance | m |
| \(s_{2}\) | Dimension 2: direction (+1 adds, −1 subtracts, 0 unused) | - |
| \(d_{2}\) | Dimension 2: nominal | m |
| \(t_{2}\) | Dimension 2: ± tolerance | m |
| \(s_{3}\) | Dimension 3: direction (+1 adds, −1 subtracts, 0 unused) | - |
| \(d_{3}\) | Dimension 3: nominal | m |
| \(t_{3}\) | Dimension 3: ± tolerance | m |
| \(s_{4}\) | Dimension 4: direction (+1 adds, −1 subtracts, 0 unused) | - |
| \(d_{4}\) | Dimension 4: nominal | m |
| \(t_{4}\) | Dimension 4: ± tolerance | m |
| \(s_{5}\) | Dimension 5: direction (+1 adds, −1 subtracts, 0 unused) | - |
| \(d_{5}\) | Dimension 5: nominal | m |
| \(t_{5}\) | Dimension 5: ± tolerance | m |
| \(s_{6}\) | Dimension 6: direction (+1 adds, −1 subtracts, 0 unused) | - |
| \(d_{6}\) | Dimension 6: nominal | m |
| \(t_{6}\) | Dimension 6: ± tolerance | m |
| \(G\) | Nominal gap | m |
| \(\pm t_{WC}\) | Worst-case variation | m |
| \(\pm t_{RSS}\) | RSS variation | m |
| \(G_{min}\) | Worst-case minimum gap | m |
| \(G_{max}\) | Worst-case maximum gap | m |
| \(G_{min,RSS}\) | Statistical (RSS) minimum gap | m |
| \(G_{max,RSS}\) | Statistical (RSS) maximum gap | m |
Method and standards
Linear stack.
Where it is used
- Assembly design and gap checks.
- Bearing and seal housings.
Common mistakes
- Asymmetric tolerances unconverted.
- RSS on a few parts.
Assumptions and limits
Each direction is chosen as +1, −1 or 0; other values are rejected. A negative minimum gap (interference) is flagged.
Linear one-dimensional chain.
References
- Worst case Σt_i; statistical RSS √Σt_i² (tolerance analysis practice)
Questions and answers
A 100 ± 0.1 housing with three parts 40, 30 and 29.5 ± 0.05?
Gap 0.5 mm ± 0.25 worst case, ± 0.132 RSS.
Which to use?
Worst case for safety-critical fits; RSS for high-volume parts with process control.
Asymmetric tolerances?
Convert to a mean size and an equal ± tolerance first.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.