FireCADCalc

Casting Gating System: Choke Area, Runner and Gates

Choke area to pour a casting in a set time from mass, metal density, sprue height and efficiency, with runner and gate areas from the gating ratio.

Thermal power plantProcess steam and utilitiesSugar mill and cogeneration

Inputs

Examples: 50 kg iron in 20 s, 300 mm sprue, 1:2:2Aluminium 8 kg in 12 s, 1:4:4

Results

Effective height: h for top gating, h − p/2 for parting-line gating, h − p²/(2c) for bottom gating (p = casting height above the gate). Pressurised ratios (1:2:2) suit iron; unpressurised (1:4:4) suit aluminium.

Choke area147.58mm²
Round choke diameter13.708mm
Runner area590.33mm²
Total gate area590.33mm²
Velocity at the choke1.8822m/s

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50 kg iron in 20 s, 300 mm sprue, 1:2:2. The inputs, in the units selected above:

InputValue
Poured mass (casting + gating)50.000 kg
Liquid metal density7,000.0 kg/m³
Pouring time20.000 s
Effective sprue height0.30000 m
Efficiency (discharge) factor0.80000 -
Runner area ratio to choke2.0000 -
Total gate area ratio to choke2.0000 -

Applying the formula below gives:

ResultValue
Choke area184.04 mm²
Round choke diameter15.308 mm
Runner area368.08 mm²
Total gate area368.08 mm²
Velocity at the choke1.9406 m/s

Open this example in the calculator and change any input.

Formula

\(A_c = \frac{W}{\rho tc\sqrt{2gh}}, \quad A_r = r_rA_c, \quad A_g = r_gA_c\)

Variables

Symbol Meaning SI unit
\(W\) Poured mass (casting + gating) kg
\(\rho\) Liquid metal density kg/m³
\(t\) Pouring time s
\(h\) Effective sprue height m
\(c\) Efficiency (discharge) factor -
\(r_r\) Runner area ratio to choke -
\(r_g\) Total gate area ratio to choke -
\(A_c\) Choke area m²
\(d_c\) Round choke diameter m
\(A_r\) Runner area m²
\(A_g\) Total gate area m²
\(v_c\) Velocity at the choke m/s

Method and standards

Bernoulli at the choke.

Where it is used

  • Foundry gating design.
  • Teaching and exam problems.

Common mistakes

  • Using total sprue height for bottom gating.
  • Ignoring friction (c).

Assumptions and limits

  • Steady flow; constant head.
  • The choke velocity is not checked against the critical gate velocity for surface turbulence (Campbell gives about 0.5 m/s for most liquid metals at the gate): gates are normally enlarged so the metal enters slowly.

References

  • Bernoulli flow through the choke A_c = W/(ρtc√(2gh)) (Campbell, Castings, 2nd ed.; Rao, Manufacturing Technology: Foundry)

Questions and answers

Why control pouring time?

Too slow and the metal freezes before filling (cold shuts); too fast and turbulence entrains sand and oxide.

What is the choke?

The smallest section of the gating system; it controls the flow rate.

What do the defaults represent?

A 50 kg steel or iron casting poured in 20 s through a 300 mm sprue with a 1:2:2 gating ratio.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.