FireCADCalc

Sheet Metal Bend Allowance, Bend Deduction and Flat Length

Bend allowance, outside setback and bend deduction of a sheet-metal bend from angle, inside radius, thickness and K-factor, with the flat length of an L-bend.

Inputs

Examples: 90° bend, R 3, t 2120° bend, R 1, t 1.5

From your bend tests; often about 0.3–0.45.

Results

Bend allowance θ(R + Kt)3.3510mm
Outside setback tan(θ/2)(R + t)4.3301mm
Bend deduction 2 OSSB − BA5.3092mm
Flat length A + B − BD74.691mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 90° bend, R 3, t 2. The inputs, in the units selected above:

InputValue
Bend angle (deflection from flat, not the included angle)90.000 °
Inside bend radius3.0000 mm
Sheet thickness2.0000 mm
K-factor0.33000 -
Flange A (outside dimension)50.000 mm
Flange B (outside dimension)30.000 mm

Applying the formula below gives:

ResultValue
Bend allowance θ(R + Kt)5.7491 mm
Outside setback tan(θ/2)(R + t)5.0000 mm
Bend deduction 2 OSSB − BA4.2509 mm
Flat length A + B − BD75.749 mm

Open this example in the calculator and change any input.

Formula

\(BA = \theta(R + Kt), \quad OSSB = \tan\frac{\theta}{2}(R + t), \quad BD = 2\,OSSB - BA\)

Variables

Symbol Meaning SI unit
\(\theta\) Bend angle (deflection from flat, not the included angle) rad
\(R\) Inside bend radius m
\(t\) Sheet thickness m
\(K\) K-factor -
\(A\) Flange A (outside dimension) m
\(B\) Flange B (outside dimension) m
\(BA\) Bend allowance θ(R + Kt) m
\(OSSB\) Outside setback tan(θ/2)(R + t) m
\(BD\) Bend deduction 2 OSSB − BA m
\(L_f\) Flat length A + B − BD m

Method and standards

Neutral-axis geometry.

Where it is used

  • Ducting, panels and enclosures.
  • Flat pattern development.

Common mistakes

  • Bend angle vs included angle.
  • Inside vs outside dimensions.

Assumptions and limits

  • Single bend, constant K.
  • θ is the bend (deflection) angle from flat: a 90° bend has θ = 90°; a part whose flanges meet at an included angle of 120° has θ = 60°.
  • A flange shorter than the outside setback, or a flat length of zero or less, is flagged.

References

  • Bend allowance BA = θ(R + Kt); bend deduction BD = 2 tan(θ/2)(R + t) − BA (sheet-metal practice)

Questions and answers

90° bend, R 3, t 2, K 0.33, flanges 50 and 30?

BA 5.75 mm, BD 4.25 mm, flat 75.75 mm.

What is the K-factor?

Where the neutral axis sits through the thickness.

Get K from tests?

Bend a strip, measure, and back-calculate.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.