Worked example
Example: Turbine hall, 15 m. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Free area of the low openings | 4.0000 m² |
| Free area of the high openings | 4.0000 m² |
| Height between opening centres | 15.000 m |
| Indoor temperature | 40.000 °C |
| Outdoor temperature | 30.000 °C |
| Discharge coefficient | 0.61000 - |
| Air density for the heat removed | 1.2000 kg/m³ |
Applying the formula below gives:
| Result | Value |
|---|---|
| Effective area (openings in series) | 2.8284 m² |
| Stack flow | 19,038 m³/h |
| Heat removed ρ c_p V ΔT (c_p 1006 J/(kg·K)) | 63.841 kW |
Open this example in the calculator and change any input.
Formula
\(\dot V = C_d A_e\sqrt{\frac{2 g H |T_i - T_o|}{T_w}}, \quad T_w = \max(T_i, T_o), \quad \frac{1}{A_e^2} = \frac{1}{A_1^2} + \frac{1}{A_2^2}, \quad \dot Q = \rho c_p \dot V |T_i - T_o|\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(A_1\) | Free area of the low openings | m² |
| \(A_2\) | Free area of the high openings | m² |
| \(H\) | Height between opening centres | m |
| \(T_i\) | Indoor temperature | K |
| \(T_o\) | Outdoor temperature | K |
| \(C_d\) | Discharge coefficient | - |
| \(A_e\) | Effective area (openings in series) | m² |
| \(\dot V\) | Stack flow | m³/s |
| \(\dot Q\) | Heat removed ρ c_p V ΔT (c_p 1006 J/(kg·K)) | W |
| \(\rho\) | Air density for the heat removed | kg/m³ |
| \(c_p\) | Specific heat of air, 1 006 | J/(kg·K) |
| \(T_w\) | The warmer of T_i and T_o (absolute) | K |
| \(g\) | Standard gravity, 9.806 65 | m/s² |
Method and standards
Bernoulli with buoyancy.
Where it is used
- Turbine halls, boiler houses and warehouses.
- Smoke and heat vents.
Common mistakes
- Gross instead of free area.
- Ignoring wind.
Assumptions and limits
- Still air, well-mixed interior.
- The buoyancy term divides by the warmer absolute temperature, so the same formula holds when the inside is colder than outside (flow reversed).
- The air density for the heat removed is an input (default 1.2 kg/m³); use the density at the outlet air temperature, about 1.13 kg/m³ at 40 °C.
References
- Buoyancy-driven flow Q = C_d A_e √(2gHΔT/T)
- openings in series 1/A_e² = 1/A₁² + 1/A₂² (CIBSE AM10; ASHRAE Handbook—Fundamentals ch. 16)
Questions and answers
4 m² low and high, 15 m apart, 40 °C inside, 30 °C out?
About 5.3 m³/s (19,000 m³/h), removing some 64 kW.
Why combine the areas?
Air must pass both; the smaller one controls.
Turbine halls?
Tall halls with roof monitors rely on this.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.