FireCADCalc

Clean Room Air Flow for a Particle Class

Supply air flow and air changes a clean room needs to hold its ISO 14644-1 class concentration against particle generation from people and processes.

Distillery and ethanolChemical and fertiliserFood, dairy and textile

Inputs

Examples: ISO 7 at 0.5 µm, four peopleISO 8 at 0.5 µm, ten people, 40 m³

Results

Class limit from the ISO 14644-1 formula C_n = 10^N(0.1/D)^2.08 (D in µm). Steady mixing model; designers usually apply a safety factor of 2 or more and check recovery time. Unidirectional (laminar) rooms are sized by velocity, not by this model.

Class limit (particles/m³)351,676
Total generation (particles/s)410,000
Supply air flow5,246.3m³/h
Air changes per hour17.488

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: ISO 7 at 0.5 µm, four people. The inputs, in the units selected above:

InputValue
ISO class number7.0000 -
Particle size considered0.50000 µm
Particles per person per second (≥ D)100,000 -
People in the room4.0000 -
Other generation (particles/s)10,000 -
Supply air concentration (particles/m³)0 -
Ventilation effectiveness80.000 %
Room volume300.00 m³

Applying the formula below gives:

ResultValue
Class limit (particles/m³)351,676
Total generation (particles/s)410,000
Supply air flow5,246.3 m³/h
Air changes per hour17.488

Open this example in the calculator and change any input.

Formula

\(C_n = 10^N\left(\frac{0.1}{D}\right)^{2.08}, \quad \dot V = \frac{G}{\varepsilon_v(C_n - C_s)}\)

Variables

Symbol Meaning SI unit
\(N\) ISO class number -
\(D\) Particle size considered m
\(g_p\) Particles per person per second (≥ D) -
\(n\) People in the room -
\(G_o\) Other generation (particles/s) -
\(C_s\) Supply air concentration (particles/m³) -
\(\varepsilon_v\) Ventilation effectiveness -
\(V\) Room volume m³
\(C_n\) Class limit (particles/m³) -
\(G\) Total generation (particles/s) -
\(\dot V\) Supply air flow m³/s
\(ACH\) Air changes per hour -

Method and standards

Particle balance.

Where it is used

  • Pharma, food and electronics clean rooms.
  • Control and instrument rooms.

Common mistakes

  • Ignoring people generation.
  • Designing with no safety factor.

Assumptions and limits

  • Non-unidirectional (mixed) flow; steady state.
  • No safety factor is applied: the flow holds the room exactly at the class limit. Multiply by your design factor (often 2 or more).

References

  • ISO 14644-1 class formula C_n = 10^N(0.1/D)^2.08; steady well-mixed particle balance (ASHRAE Handbook—HVAC Applications (2019), ch. 19)

Questions and answers

Why are people the main source?

A person sheds 10⁵–10⁷ particles per minute depending on garments and activity; gowning cuts this sharply.

Why do real clean rooms use more air?

Designers add safety factors for recovery after doors open, uneven mixing and process upsets.

What do the defaults represent?

An ISO 7 room at 0.5 µm with four gowned people and HEPA-filtered supply.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.