FireCADCalc

Screen Efficiency and Circulating Load

Screen efficiency from the fines in feed, oversize and undersize, the mass split between the two products, and the circulating load of a closed circuit.

Thermal power plantDistillery and ethanolRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 60 % fines feed, 100 t/hFine screen, poor separation

Results

Efficiency here is the product of fines recovery to the undersize and coarse recovery to the oversize (Perry's). Fractions are of the cut size.

Undersize (product) rate15.385t/h
Oversize rate34.615t/h
Screen efficiency60.355%
Circulating load (oversize/undersize = recycle/new feed at steady state)225.00%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 60 % fines feed, 100 t/h. The inputs, in the units selected above:

InputValue
Fines (passing size) in the feed60.000 %
Fines in the oversize (reject)10.000 %
Fines in the undersize (product)95.000 %
Feed rate100.00 t/h

Applying the formula below gives:

ResultValue
Undersize (product) rate58.824 t/h
Oversize rate41.176 t/h
Screen efficiency86.289 %
Circulating load (oversize/undersize = recycle/new feed at steady state)70.000 %

Open this example in the calculator and change any input.

Formula

\(\dot m_U = \dot m_F\frac{f - c}{u - c}, \quad E = \frac{u\dot m_U}{f\dot m_F}\cdot\frac{(1 - c)\dot m_O}{(1 - f)\dot m_F}\)

Variables

Symbol Meaning SI unit
\(f\) Fines (passing size) in the feed -
\(c\) Fines in the oversize (reject) -
\(u\) Fines in the undersize (product) -
\(\dot m_F\) Feed rate kg/s
\(\dot m_U\) Undersize (product) rate kg/s
\(\dot m_O\) Oversize rate kg/s
\(E\) Screen efficiency -
\(CL\) Circulating load (oversize/undersize = recycle/new feed at steady state) -

Method and standards

Material balance on the cut size.

Where it is used

  • Crushing and grinding circuits.
  • Screen performance checks.

Common mistakes

  • Sampling streams at different times.
  • Mixing size bases.

Assumptions and limits

  • Steady state; two products.
  • The circulating load is oversize over undersize. In a closed mill circuit it equals mill recycle over new feed only at steady state, when the screen product equals the new feed.

References

  • Perry's Chemical Engineers' Handbook
  • 9th ed. (McGraw-Hill, 2019)
  • sec. 19 (screening efficiency and material balance)

Questions and answers

Why not just the product's fines content?

A screen can give a clean product while losing many fines to the oversize; efficiency counts both recoveries.

What is circulating load?

The oversize returned to the mill per unit of product; 100–300 % is common in closed grinding circuits.

What do the defaults represent?

A screen on a crushing circuit with 60 % fines in the feed.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.