FireCADCalc

Just-Suspended Impeller Speed for Solids (Zwietering)

Impeller speed to just suspend all solids in a stirred tank (Zwietering) from particle size and density, liquid properties, loading and impeller size.

Distillery and ethanolRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 200 µm sand 10 %, 1 m PBTCrystals 500 µm, 25 %, 0.6 m

Not wt % of slurry: a 10 wt % slurry is X = 100 × 10/90 = 11.1.

Results

S depends on impeller type and clearance and tank-to-impeller ratio (about 4–8 for pitched-blade turbines at T/D = 3 with one-quarter clearance); take it from Zwietering's charts or tests. SI units throughout.

Just-suspended speed84.202rpm
Tip speed4.4088m/s

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 200 µm sand 10 %, 1 m PBT. The inputs, in the units selected above:

InputValue
Zwietering geometry constant6.5000 -
Liquid kinematic viscosity1.0000 cSt
Particle size200.00 µm
Solid density2,650.0 kg/m³
Liquid density1,000.0 kg/m³
Solids loading (mass solids per 100 mass liquid)10.000 -
Impeller diameter1.0000 m

Applying the formula below gives:

ResultValue
Just-suspended speed84.202 rpm
Tip speed4.4088 m/s

Open this example in the calculator and change any input.

Formula

\(N_{js} = S\,\nu^{0.1}\left(\frac{g\Delta\rho}{\rho_L}\right)^{0.45}X^{0.13}d_p^{0.2}D^{-0.85}\)

Variables

Symbol Meaning SI unit
\(S\) Zwietering geometry constant -
\(\nu\) Liquid kinematic viscosity m²/s
\(d_p\) Particle size m
\(\rho_s\) Solid density kg/m³
\(\rho_L\) Liquid density kg/m³
\(X\) Solids loading (mass solids per 100 mass liquid) -
\(D\) Impeller diameter m
\(N_{js}\) Just-suspended speed 1/s
\(\pi DN_{js}\) Tip speed m/s

Method and standards

Zwietering correlation (SI).

Where it is used

  • Slurry tanks, crystallisers and leach tanks.
  • Agitator selection.

Common mistakes

  • Using an S for another impeller.
  • X as a fraction rather than per 100 parts.

Assumptions and limits

  • Standard baffled tanks.
  • X is mass of solids per 100 mass of liquid, not wt % of slurry (10 wt % slurry is X = 11.1).

References

  • Zwietering (1958)
  • Chem. Eng. Sci. 8: 244; Perry's Chemical Engineers' Handbook
  • 9th ed. (McGraw-Hill, 2019)
  • sec. 18 (solids suspension)

Questions and answers

Why just-suspended?

Above N_js no particle rests on the base for more than a moment; most dissolution and reaction duties need about this speed, not full uniformity.

How does speed scale with tank size?

At constant geometry N_js ∝ D^−0.85, so power per volume falls somewhat on scale-up.

What do the defaults represent?

Sand-like 200 µm solids at 10 % in water with a 1 m pitched-blade turbine.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.