Worked example
Example: Five fractions 1 mm to 60 µm. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Mean size of fraction 1 | 1,000.0 µm |
| Mass fraction 1 | 10.000 % |
| Mean size of fraction 2 | 600.00 µm |
| Mass fraction 2 | 30.000 % |
| Mean size of fraction 3 | 300.00 µm |
| Mass fraction 3 | 30.000 % |
| Mean size of fraction 4 | 150.00 µm |
| Mass fraction 4 | 20.000 % |
| Mean size of fraction 5 | 60.000 µm |
| Mass fraction 5 | 10.000 % |
| Mean size of fraction 6 (0 = none) | 0 µm |
| Mass fraction 6 | 0 % |
| Particle density | 2,650.0 kg/m³ |
| Sphericity | 80.000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Sauter mean (surface–volume) | 217.39 µm |
| Mass-weighted mean | 406.00 µm |
| Specific surface area | 13.019 m²/kg |
| Sum of mass fractions | 100.00 % |
Open this example in the calculator and change any input.
Formula
\(d_{32} = \frac{\sum x_i}{\sum x_i/d_i}, \quad d_{43} = \frac{\sum x_id_i}{\sum x_i}, \quad S_m = \frac{6}{\phi_s\rho_pd_{32}}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(d_1\) | Mean size of fraction 1 | m |
| \(x_1\) | Mass fraction 1 | - |
| \(d_2\) | Mean size of fraction 2 | m |
| \(x_2\) | Mass fraction 2 | - |
| \(d_3\) | Mean size of fraction 3 | m |
| \(x_3\) | Mass fraction 3 | - |
| \(d_4\) | Mean size of fraction 4 | m |
| \(x_4\) | Mass fraction 4 | - |
| \(d_5\) | Mean size of fraction 5 | m |
| \(x_5\) | Mass fraction 5 | - |
| \(d_6\) | Mean size of fraction 6 (0 = none) | m |
| \(x_6\) | Mass fraction 6 | - |
| \(\rho_p\) | Particle density | kg/m³ |
| \(\phi_s\) | Sphericity | - |
| \(d_{32}\) | Sauter mean (surface–volume) | m |
| \(d_{43}\) | Mass-weighted mean | m |
| \(S_m\) | Specific surface area (m²/kg) | - |
| \(\Sigma x\) | Sum of mass fractions | - |
Method and standards
Size statistics.
Where it is used
- Grinding, drying and combustion of solids.
- Packed and fluidised bed design.
Common mistakes
- Using sieve opening rather than fraction mean size.
- Ignoring sphericity in specific surface.
Assumptions and limits
- Fraction mean sizes represent each cut.
- The specific surface is shown in m²/kg in every unit system (there is no unit list for area per mass yet).
References
- Perry's Chemical Engineers' Handbook
- 9th ed. (McGraw-Hill, 2019)
- sec. 21 (particle size statistics; specific surface 6/(φρd))
Questions and answers
Which mean should I use?
Sauter d₃₂ for surface processes (reaction, heat and mass transfer, drag in packed beds); mass mean d₄₃ for settling and mass balances.
What is sphericity?
Surface of a sphere of the same volume divided by the particle's surface: 1 for spheres, about 0.6–0.8 for crushed solids.
What do the defaults represent?
A sand-like powder in five sieve fractions from 1 mm to 60 µm.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.