FireCADCalc

Dühring Rule: Boiling Point of a Solution at Any Pressure

Boiling point of a solution at a new pressure from two measured boiling points against water's boiling points (a straight Dühring line); water from IAPWS-IF97.

Sugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textileIAPWS-IF97 (water and steam)

Inputs

Examples: Solution 108/100 and 67/60 °C, at 20 kPaCaustic 50 %

Results

Slope of the Dühring line1.0400
Water boiling point at p81.317°C
Solution boiling point at p122.57°C
Boiling-point rise41.253K

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Solution 108/100 and 67/60 °C, at 20 kPa. The inputs, in the units selected above:

InputValue
Water boiling point, reference 1100.00 °C
Solution boiling point, reference 1108.00 °C
Water boiling point, reference 260.000 °C
Solution boiling point, reference 267.000 °C
New pressure (absolute)20.000 kPa

Applying the formula below gives:

ResultValue
Slope of the Dühring line1.0250
Water boiling point at p60.059 °C
Solution boiling point at p67.060 °C
Boiling-point rise7.0015 K

Open this example in the calculator and change any input.

Formula

\(T_s = T_{s1} + K(T_w - T_{w1}), \quad K = \frac{T_{s1} - T_{s2}}{T_{w1} - T_{w2}}\)

Variables

Symbol Meaning SI unit
\(T_{w1}\) Water boiling point, reference 1 K
\(T_{s1}\) Solution boiling point, reference 1 K
\(T_{w2}\) Water boiling point, reference 2 K
\(T_{s2}\) Solution boiling point, reference 2 K
\(p\) New pressure (absolute) Pa
\(K\) Slope of the Dühring line -
\(T_w\) Water boiling point at p K
\(T_s\) Solution boiling point at p K
\(BPR\) Boiling-point rise K

Method and standards

Linear Dühring line with IF97 water saturation.

Where it is used

  • Multiple-effect evaporator design.
  • Caustic, sugar and salt solutions.

Common mistakes

  • Using data for another concentration.
  • Gauge instead of absolute pressure.

Assumptions and limits

  • One fixed concentration.
  • Reference points with the solution boiling below water are rejected; a note appears when the water boiling point at p is more than one reference span outside the two references (extrapolation).

References

  • Perry's Chemical Engineers' Handbook
  • 9th ed. (McGraw-Hill, 2019)
  • sec. 11 (evaporators): Dühring's rule
  • Water saturation temperature from IAPWS-IF97

Questions and answers

What is Dühring's rule?

For a solution of fixed concentration, its boiling point is a straight-line function of water's boiling point at the same pressure.

Why two reference points?

They fix the slope and intercept of the line for that concentration.

Does it hold far outside the data?

Approximately; it is best between the reference pressures.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.