Worked example
Example: Indian coal 0.5 % S, 25 % excess air, at 6 % O2. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Carbon | 45.000 % |
| Hydrogen | 3.5000 % |
| Oxygen | 5.0000 % |
| Nitrogen | 1.0000 % |
| Sulphur | 0.50000 % |
| Ash | 35.000 % |
| Moisture | 10.000 % |
| Excess air | 25.000 % |
| Air humidity (kg water per kg dry air) | 0.013000 kg/kg |
| Reference O₂ of the emission limit (dry) | 6.0000 % |
| O₂ in air used by the rule | 20.950 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| SO₂ at reference O₂, dry, normal | 1,538.1 mg/Nm³ |
| SO₂ at actual O₂, dry, normal | 1,713.1 mg/Nm³ |
| Actual O₂ in dry flue gas | 4.2989 % |
| SO₂ per kg of fuel | 9.9903 g/kg |
| Dry flue gas per kg of fuel | 5.8317 Nm³/kg |
Open this example in the calculator and change any input.
Formula
\(m_{SO_2} = S\,\frac{M_{SO_2}}{M_S} \qquad c = \frac{m_{SO_2}}{V_{dg}} \qquad c_{ref} = c\,\frac{O_{2,air} - O_{2,ref}}{O_{2,air} - O_2}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(C, H, O, N, S, A, M\) | ultimate analysis as fired | – |
| \(EA\) | excess air | – |
| \(\omega\) | air humidity | kg/kg |
| \(O_{2,ref}\) | reference O₂ (dry) | – |
| \(O_{2,air}\) | O₂ in air used by the rule (20.95 % physical; 21 % EU IED and Indian practice; 20.9 % US EPA) | – |
| \(c_{ref}\) | SO₂ at reference O₂ | kg/m³ |
| \(c\) | SO₂ at actual O₂ | kg/m³ |
| \(O_2\) | actual O₂ in dry flue gas | – |
| \(m_{SO_2}\) | SO₂ per kg fuel | kg/kg |
| \(V_{dg}\) | dry flue gas per kg fuel at normal conditions | m³/kg |
| \(M_{SO_2}, M_S\) | molar masses | kg/kmol |
Method and standards
Exact-ratio combustion balance with all fuel sulphur as SO₂; dry gas volume at 0 °C and 101.325 kPa; O₂ correction to the reference.
Where it is used
- Checking a fuel against SO₂ limits.
- Sizing FGD or limestone injection.
- Permit applications.
Common mistakes
- Using wet gas volume against dry-basis limits.
- Correcting to the wrong reference O₂ for the fuel.
- Using air-dried sulphur with as-fired flue gas.
Assumptions and limits
- All sulphur to SO₂ (SO₃ and ash retention neglected); complete combustion.
References
- Stoichiometry S + O₂ → SO₂ with the exact-ratio flue gas balance
Questions and answers
How much SO₂ does 0.5 % sulphur coal give?
At 25 % excess air (enter 25 %; the page opens at 20 %) the dry flue gas holds 1713 mg/Nm³ of SO₂ at its actual 4.3 % O₂, or 1538 mg/Nm³ at the 6 % O₂ reference often used for coal.
Why correct to a reference O₂?
So that diluting the gas with air cannot meet a limit; limits are stated at a fixed O₂ for each fuel.
Is all the sulphur emitted?
This assumes so; some stays in alkaline ash, and limestone in a fluidised bed captures much more.
Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.