Worked example
Example: 20 t/h corn, 31 % solids, jet 120 °C. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Grain (meal) to the slurry | 20.000 t/h |
| Grain share of the slurry | 31.000 % |
| Specific heat of the grain solids | 1.5500 kJ/(kg·K) |
| Slurry temperature | 60.000 °C |
| Jet cooker temperature | 120.00 °C |
| Liquefaction (flash) temperature | 85.000 °C |
| Cooking steam pressure (absolute) | 8.0000 bar |
| Liquefaction residence | 60.000 min |
| Mash density | 1,100.0 kg/m³ |
| α-amylase dose (w/w grain) | 0.060000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Slurry | 64.516 t/h |
| Slurry specific heat | 3.3694 kJ/(kg·K) |
| Cooking steam | 5,759.6 kg/h |
| Steam per tonne grain | 287.98 kg/t |
| Vapour flashed to liquefaction temperature | 3,610.5 kg/h |
| Liquefaction tank working volume | 60.605 m³ |
| α-amylase | 12.000 kg/h |
Open this example in the calculator and change any input.
Formula
\(M = \frac{G}{x}, \quad c = xc_s + (1 - x)c_w, \quad \dot m_s = \frac{Mc(T_j - T_0)}{h_g(p_s) - h_f(T_j)}, \quad \dot m_f = \frac{(M + \dot m_s)c(T_j - T_f)}{h_{fg}(T_f)}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(G\) | Grain (meal) to the slurry | kg/s |
| \(x\) | Grain share of the slurry | - |
| \(c_s\) | Specific heat of the grain solids | J/(kg·K) |
| \(T_0\) | Slurry temperature | K |
| \(T_j\) | Jet cooker temperature | K |
| \(T_f\) | Liquefaction (flash) temperature | K |
| \(p_s\) | Cooking steam pressure (absolute) | Pa |
| \(t_r\) | Liquefaction residence | s |
| \(\rho_m\) | Mash density | kg/m³ |
| \(e\) | α-amylase dose (w/w grain) | - |
| \(M\) | Slurry | kg/s |
| \(c\) | Slurry specific heat | J/(kg·K) |
| \(\dot m_s\) | Cooking steam | kg/s |
| \(\dot m_s/G\) | Steam per tonne grain | kg/kg |
| \(\dot m_f\) | Vapour flashed to liquefaction temperature | kg/s |
| \(V\) | Liquefaction tank working volume | m³ |
| \(\dot m_E\) | α-amylase | kg/s |
| \(c_w\) | Specific heat of water, 4.1868 kJ/(kg·K) | J/(kg·K) |
| \(h_g, h_f, h_{fg}\) | Saturated steam, saturated liquid and latent enthalpies (IAPWS-IF97) | J/kg |
Method and standards
Heat balance for direct steam injection and adiabatic flash.
Where it is used
- Cooking system design.
- Steam budgets for grain distilleries.
Common mistakes
- Leaving out backset in the slurry.
- Using indirect heating figures for jet cookers.
Assumptions and limits
- Steam condenses fully in the mash; no heat loss.
- c_w, the specific heat of water, is taken as 4.1868 kJ/(kg·K); the default c_s of 1.55 kJ/(kg·K) is a starting value without a particular source.
- The supply steam is taken as dry saturated at p_s; superheated or wet steam is not handled.
References
- Jacques
- Lyons and Kelsall (eds.)
- The Alcohol Textbook
- 4th ed. (Nottingham University Press, 2003)
- ch. 2 (Kelsall and Lyons)
- cooking systems
- Steam and water enthalpies from IAPWS-IF97
Questions and answers
Why a jet cooker?
Steam injected directly heats the mash instantly to 120–140 °C, gelatinising starch so enzymes can act.
Why flash after the jet?
Dropping to 80–90 °C cools the mash for liquefaction and gives vapour that can preheat the slurry.
Why does solids content matter?
Thicker slurries need less steam per tonne of grain and give stronger beer, but are harder to pump.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.