FireCADCalc

Particle Terminal (Settling) Velocity

Terminal settling velocity of a spherical particle in a gas or liquid, by the Haider–Levenspiel drag correlation, with Reynolds number, drag coefficient and the Stokes value.

Process steam and utilitiesRefinery and petrochemicalChemical and fertiliserBoilerDust collector (ESP, bag filter, cyclone)

Inputs

Examples: Sand 100 µm in airFly ash 20 µm in flue gas at 300 °CSand 0.5 mm in water

Results

Single smooth sphere in still fluid; irregular particles settle more slowly, and crowding (hindered settling) slows them further.

Terminal velocity0.015868m/s
Particle Reynolds number0.006347
Drag coefficient3,807.3
Stokes-law velocity (valid for Re below about 0.3)0.015977m/s

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Sand 100 µm in air. The inputs, in the units selected above:

InputValue
Particle diameter100.00 µm
Particle density2,500.0 kg/m³
Fluid density1.2000 kg/m³
Fluid dynamic viscosity1.8000e-05 Pa·s

Applying the formula below gives:

ResultValue
Terminal velocity0.53597 m/s
Particle Reynolds number3.5732
Drag coefficient9.4781
Stokes-law velocity (valid for Re below about 0.3)0.75632 m/s

Open this example in the calculator and change any input.

Formula

\(C_D\, Re^2 = \frac{4 g d_p^3 \rho_f (\rho_p - \rho_f)}{3 \mu^2}\)

\(C_D = \frac{24}{Re}\left(1 + 0.1806\, Re^{0.6459}\right) + \frac{0.4251}{1 + 6880.95/Re}\)

\(v_t = \frac{Re\, \mu}{\rho_f d_p}, \quad v_{St} = \frac{g d_p^2 (\rho_p - \rho_f)}{18 \mu}\)

Variables

Symbol Meaning SI unit
\(d_p\) particle diameter m
\(\rho_p\) particle density kg/m³
\(\rho_f\) fluid density kg/m³
\(\mu\) fluid dynamic viscosity Pa·s
\(g\) standard gravity m/s²
\(v_t\) terminal velocity m/s
\(Re\) particle Reynolds number -
\(C_D\) drag coefficient -
\(v_{St}\) Stokes-law velocity m/s

Method and standards

At terminal velocity weight less buoyancy equals drag. The product C_D Re² depends only on the particle and fluid, so Re is found from it with the Haider–Levenspiel (1989) sphere correlation, valid up to Re 2.6×10⁵, and the velocity follows. The Stokes value is shown for comparison.

Where it is used

  • Checking carry-over from fluidised beds and furnaces.
  • Sizing settling chambers and drop-out boxes.
  • Estimating ash deposition in low-velocity ducts.

Common mistakes

  • Using Stokes' law at Reynolds numbers well above 1.
  • Using bulk density for the particle density.
  • Ignoring that irregular particles settle more slowly than spheres.

Assumptions and limits

  • Single smooth sphere in still, unbounded fluid; sphericity is not an input, and irregular particles settle more slowly than the value shown.
  • No hindered settling (dilute suspension).
  • Re up to 2.6×10⁵.

References

  • Haider and Levenspiel (1989)
  • Powder Technology 58
  • eq. 6
  • Stokes' law

Questions and answers

How fast does 100 µm sand settle in air?

About 0.54 m/s. Stokes' law would say 0.76 m/s, but at Re about 3.6 the drag is already higher than Stokes allows.

When is Stokes' law good enough?

Below a particle Reynolds number of about 0.3; fine fly ash of 20 µm settles at about 16 mm/s, close to the Stokes value.

Why does this matter for boilers?

It sets which particles a gas stream carries out of a furnace, bed or duct, and how fast ash settles in hoppers and ducts.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.