FireCADCalc

Slurry Minimum Transport Velocity (Durand and Spells)

Minimum velocity to keep a settling slurry from forming a deposit (Durand), velocity for full symmetric suspension (Spells) and the matching flow.

Thermal power plantSugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: Sand in water, DN150, 15 %Fly ash, DN250, 10 %

Results

Design above V_M2 with a margin; typical settling-slurry velocities are 1–4 m/s (Perry's). Above V_M2, pressure drop is about 25 % above that of a uniform fluid of the slurry density.

Slurry density1,245.8kg/m³
Minimum transport (deposition) velocity3.3551m/s
Flow at the minimum velocity225.27m³/h
Velocity for symmetric suspension (Spells)5.2181m/s

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Sand in water, DN150, 15 %. The inputs, in the units selected above:

InputValue
Pipe inside diameter154.10 mm
Solid density2,650.0 kg/m³
Liquid density998.00 kg/m³
Solids volume fraction15.000 %
Durand factor F_L (1.5 conservative)1.5000 -
Particle size (85 % by mass smaller)0.50000 mm
Liquid viscosity1.0000 cP

Applying the formula below gives:

ResultValue
Slurry density1,245.8 kg/m³
Minimum transport (deposition) velocity3.3551 m/s
Flow at the minimum velocity225.27 m³/h
Velocity for symmetric suspension (Spells)5.2181 m/s

Open this example in the calculator and change any input.

Formula

\(V_{M2} = F_L\sqrt{2gD(s - 1)}, \quad V_{M1}^2 = 0.075\left(\frac{DV_{M1}\rho_M}{\mu}\right)^{0.775}gD_S(s - 1), \quad s = \frac{\rho_S}{\rho_L}\)

Variables

Symbol Meaning SI unit
\(D\) Pipe inside diameter m
\(\rho_S\) Solid density kg/m³
\(\rho_L\) Liquid density kg/m³
\(C_S\) Solids volume fraction -
\(F_L\) Durand factor F_L (1.5 conservative) -
\(D_S\) Particle size (85 % by mass smaller) m
\(\mu\) Liquid viscosity Pa·s
\(\rho_M\) Slurry density kg/m³
\(V_{M2}\) Minimum transport (deposition) velocity m/s
\(Q_{min}\) Flow at the minimum velocity m³/s
\(V_{M1}\) Velocity for symmetric suspension (Spells) m/s

Method and standards

Durand and Spells correlations.

Where it is used

  • Ash slurry disposal lines.
  • Lime, sand and mineral slurries.

Common mistakes

  • Using it for non-settling (fine, concentrated) slurries.
  • Designing at the deposition velocity with no margin.

Assumptions and limits

  • Settling slurries in horizontal pipes.
  • The two velocities answer different questions: V_M2 (Durand) is the limit below which a stationary deposit forms; V_M1 (Spells) is the velocity for full, symmetric suspension. They can differ widely (in the fly-ash preset Spells gives 1.39 m/s and Durand 2.45 m/s). Design above V_M2 with a margin; where V_M1 is the larger, run near it only if a fully suspended profile is needed, since wear rises with velocity.

References

  • Perry's Chemical Engineers' Handbook
  • 9th ed. (McGraw-Hill, 2019)
  • sec. 6
  • Eqs. (6-150) (Durand) and (6-152) (Spells)

Questions and answers

What happens below the deposition velocity?

Solids settle and form a bed; pressure gradient rises sharply and the line can block.

What F_L should I use?

Durand's chart gives 0.4–1.5 by particle size and concentration; 1.5 is the conservative design value Perry's quotes.

Is a higher velocity always better?

No: wear rises steeply with velocity. Aim a little above V_M2.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.