Worked example
Example: Shear-thinning slurry, laminar. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Consistency index K (Pa·sⁿ) | 5.0000 - |
| Flow behaviour index n | 0.50000 - |
| Density | 1,100.0 kg/m³ |
| Pipe inside diameter | 77.900 mm |
| Mean velocity | 1.5000 m/s |
| Pipe length | 100.00 m |
Applying the formula below gives:
| Result | Value |
|---|---|
| Generalised consistency K' (Pa·sⁿ) | 5.5902 |
| Metzner–Reed Reynolds number | 285.38 |
| Fanning friction factor | 0.056066 |
| Wall shear stress | 69.382 Pa |
| Pressure drop | 356.26 kPa |
| Regime (0 laminar, 1 turbulent) | 0 |
Open this example in the calculator and change any input.
Formula
\(Re_{MR} = \frac{D^nV^{2-n}\rho}{K'8^{n-1}}, \quad K' = K\left(\frac{1 + 3n}{4n}\right)^n, \quad f = \frac{16}{Re_{MR}}\ \text{(laminar)}\)
\(\frac{1}{\sqrt f} = \frac{1}{\sqrt{f_N}} + 8.2\frac{1 - n}{1 + n} + 1.77\ln\frac{1 + n}{2}, \quad \Delta p = 4f\frac{L}{D}\frac{\rho V^2}{2}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(K\) | Consistency index K (Pa·sⁿ) | - |
| \(n\) | Flow behaviour index n | - |
| \(\rho\) | Density | kg/m³ |
| \(D\) | Pipe inside diameter | m |
| \(V\) | Mean velocity | m/s |
| \(L\) | Pipe length | m |
| \(K'\) | Generalised consistency K' (Pa·sⁿ) | - |
| \(Re_{MR}\) | Metzner–Reed Reynolds number | - |
| \(f\) | Fanning friction factor | - |
| \(\tau_w\) | Wall shear stress | Pa |
| \(\Delta p\) | Pressure drop | Pa |
| \(\text{regime}\) | Regime (0 laminar, 1 turbulent) | - |
Method and standards
Metzner–Reed generalised Reynolds number; Wilson–Thomas turbulent correction; f_N for a Newtonian fluid at the wall viscosity.
Where it is used
- Polymer, food and slurry lines.
- Molasses and massecuite transfer.
Common mistakes
- Using an apparent viscosity at the wrong shear rate.
- Applying it to Bingham plastics.
Assumptions and limits
- Time-independent power-law fluids; smooth pipes.
- K is entered in Pa·sⁿ in every unit system.
- Laminar–turbulent switch at a fixed Re_MR of 2 100; the critical Reynolds number of power-law fluids depends on n (it rises for strongly shear-thinning fluids), so results near the switch are uncertain.
References
- Perry's Chemical Engineers' Handbook
- 9th ed. (McGraw-Hill, 2019)
- sec. 6
- Eqs. (6-64) to (6-69) (Metzner and Reed; Wilson and Thomas)
- Smooth-pipe Newtonian friction 1/√f = 4 log(Re√f) − 0.4 (Prandtl–Kármán)
Questions and answers
What is a power-law fluid?
One whose shear stress is K·γ̇ⁿ: n < 1 is shear-thinning (polymer solutions, many slurries, molasses at high shear), n > 1 shear-thickening.
When is the flow laminar?
Below a Metzner–Reed Reynolds number of about 2,100; most viscous non-Newtonian process lines are laminar.
Where do K and n come from?
From a viscometer: the slope and intercept of log shear stress against log shear rate.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.