FireCADCalc

Supply Air Flow and Supply State from Room Loads

Supply air mass and volume flow for a room from its sensible and latent loads, room condition and supply temperature, with the supply humidity and SHR.

Inputs

Examples: Room 24 °C 50 %, 35 + 8 kW, supply 13 °CDry room, sensible onlyHigh latent at 95 kPa, supply 14 °C

Results

Dry-air mass flow17,557kg/h
Supply air volume (at the supply state)15,486m³/h
Supply humidity ratio10.341g/kg
Supply relative humidity97.176%
Room sensible heat ratio70.588%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Room 24 °C 50 %, 35 + 8 kW, supply 13 °C. The inputs, in the units selected above:

InputValue
Room sensible load35.000 kW
Room latent load8.0000 kW
Room dry bulb24.000 °C
Room relative humidity50.000 %
Supply dry bulb13.000 °C
Barometric pressure (absolute)101.33 kPa

Applying the formula below gives:

ResultValue
Dry-air mass flow11,214 kg/h
Supply air volume (at the supply state)9,211.8 m³/h
Supply humidity ratio8.2911 g/kg
Supply relative humidity88.982 %
Room sensible heat ratio81.395 %

Open this example in the calculator and change any input.

Formula

\(\dot Q_s = \dot m_{da}(c_{pa} + W_s c_{pv})(T_r - T_s), \quad \dot Q_l = \dot m_{da}(W_r - W_s)\, h_g(T_r)\)

Variables

Symbol Meaning SI unit
\(\dot Q_s\) Room sensible load W
\(\dot Q_l\) Room latent load W
\(T_r\) Room dry bulb K
\(\varphi_r\) Room relative humidity -
\(T_s\) Supply dry bulb K
\(p\) Barometric pressure (absolute) Pa
\(\dot m_{da}\) Dry-air mass flow kg/s
\(\dot V_s\) Supply air volume (at the supply state) m³/s
\(W_s\) Supply humidity ratio kg/kg
\(\varphi_s\) Supply relative humidity -
\(SHR\) Room sensible heat ratio -

Method and standards

Energy and moisture balance on the room.

Where it is used

  • AHU and fan coil selection.
  • Control room and MCC room air conditioning.

Common mistakes

  • Volume at room instead of supply state.
  • Ignoring latent load.

Assumptions and limits

  • Steady state, perfect mixing.
  • The latent load is converted to moisture with the vapour enthalpy at room temperature, h_g = 2501 + 1.86 t kJ/kg (t in °C). Calculators that use 2501 kJ/kg alone (for example the sensible heat ratio and ADP calculator) give a supply humidity about 1–2 % different; both are common textbook forms.

References

  • Moist-air energy and moisture balances (ASHRAE Handbook—Fundamentals ch. 1 properties)

Questions and answers

35 kW sensible and 8 kW latent, room 24 °C 50 %, supply 13 °C?

About 3.1 kg/s of dry air, roughly 9,200 m³/h at the supply state.

Why does latent load change the supply humidity?

The supply air must be drier than the room by enough to absorb the moisture.

Supply RH above 100 %?

The chosen supply temperature cannot carry the latent load; lower it or add reheat.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.