FireCADCalc

Ultrafiltration Limiting Flux by the Gel-Polarisation Model

Limiting flux of an ultrafiltration membrane from the mass-transfer coefficient and gel and bulk concentrations, and at a volume reduction factor.

Distillery and ethanolRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: Whey protein 30 g/L, VRF 4Juice clarification

Results

Fully retained solute assumed. k rises with cross-flow velocity (k ∝ u^0.8 in turbulent channels); the gel concentration is a property of the solute, e.g. about 250 g/L for whey protein.

Limiting flux at the bulk concentration (L/(m²·h))114.41
Retentate concentration at the VRF50.000g/L
Limiting flux at the end of concentration (L/(m²·h))31.517

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Whey protein 30 g/L, VRF 4. The inputs, in the units selected above:

InputValue
Mass-transfer coefficient2.0000e-05 m/s
Gel (wall) concentration250.00 g/L
Bulk concentration30.000 g/L
Volume reduction factor (feed/retentate)4.0000 -

Applying the formula below gives:

ResultValue
Limiting flux at the bulk concentration (L/(m²·h))152.66
Retentate concentration at the VRF120.00 g/L
Limiting flux at the end of concentration (L/(m²·h))52.846

Open this example in the calculator and change any input.

Formula

\(J_{lim} = k\ln\frac{C_g}{C_b}, \quad C_r = C_b\cdot VRF\)

Variables

Symbol Meaning SI unit
\(k\) Mass-transfer coefficient m/s
\(C_g\) Gel (wall) concentration kg/m³
\(C_b\) Bulk concentration kg/m³
\(VRF\) Volume reduction factor (feed/retentate) -
\(J_{lim}\) Limiting flux at the bulk concentration (L/(m²·h)) -
\(C_r\) Retentate concentration at the VRF kg/m³
\(J_{lim,r}\) Limiting flux at the end of concentration (L/(m²·h)) -

Method and standards

Gel-polarisation model.

Where it is used

  • Dairy, juice and protein UF.
  • Membrane area for a batch concentration.

Common mistakes

  • Using it in the pressure-controlled region.
  • Ignoring fouling.

Assumptions and limits

  • Full rejection; film model.
  • A volume reduction that would take the retentate to the gel concentration is unreachable; it is flagged and the retentate is capped just below C_g.

References

  • Perry's Chemical Engineers' Handbook
  • 9th ed. (McGraw-Hill, 2019)
  • sec. 20 (ultrafiltration, gel-polarisation model J = k ln(C_g/C_b))

Questions and answers

Why does flux stop rising with pressure?

Above a point, retained solute forms a gel layer at the wall; more pressure only thickens it, and flux is set by back-diffusion.

How do I raise the limiting flux?

Increase cross-flow velocity or temperature, which raise k.

What do the defaults represent?

Protein ultrafiltration from 30 g/L concentrated four times.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.