FireCADCalc

Steam–Water Sampling: Line Lag Time and Sample Cooler Duty

Transit time of a sample line from bore, length and flow, and the sample cooler duty and cooling water for a hot sample (IF97 enthalpy).

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolIAPWS-IF97 (water and steam)Boiler

Inputs

Examples: Drum water 70 barSuperheated steam

Results

Transit time is for cold liquid; hot or steam samples move faster before the cooler. A velocity near 1.5–2 m/s (common practice, not a cited limit) limits deposits in the line.

The line velocity is only 0.29 m/s: iron and copper particles may settle. A smaller bore or more flow raises it.

Transit time in the line2.2619min
Sample velocity in the line (cold)0.29473m/s
Cooler duty9.6218kW
Cooling water1,034.2kg/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Drum water 70 bar. The inputs, in the units selected above:

InputValue
Sample line bore6.0000 mm
Line length40.000 m
Sample flow (cold)0.50000 L/min
Sample pressure (absolute)70.000 bar
SampleWater (liquid; saturated water at the saturation temperature)
Sample temperature (steam or water)285.00 °C
Cooled sample temperature25.000 °C
Cooling water rise8.0000 K

Applying the formula below gives:

ResultValue
Transit time in the line2.2619 min
Sample velocity in the line (cold)0.29473 m/s
Cooler duty9.6218 kW
Cooling water1,034.2 kg/h

Open this example in the calculator and change any input.

Formula

\(t_l = \frac{\pi d^2 L}{4\dot V}, \quad v = \frac{4\dot V}{\pi d^2}, \quad \dot m = \dot V\rho(T_2), \quad \dot Q = \dot m[h(p, T_1) - h(T_2)], \quad \dot m_w = \frac{\dot Q}{c_w\Delta T_w}\)

Variables

Symbol Meaning SI unit
\(d\) Sample line bore m
\(L\) Line length m
\(\dot V\) Sample flow (cold) m³/s
\(p\) Sample pressure (absolute) Pa
\(\text{sample}\) Water (liquid) or steam (dry saturated or superheated) –
\(T_1\) Sample temperature (steam or water) K
\(T_2\) Cooled sample temperature K
\(\Delta T_w\) Cooling water rise K
\(t_l\) Transit time in the line s
\(v\) Sample velocity in the line (cold) m/s
\(\dot Q\) Cooler duty W
\(\dot m_w\) Cooling water kg/s
\(\dot m\) Sample mass flow kg/s
\(\rho(T_2)\) Density of the cooled sample kg/m³
\(c_w\) Cooling water specific heat, 4 186.8 J/(kg·K)

Method and standards

Continuity; energy balance.

Where it is used

  • Sampling system design.

Common mistakes

  • Hot volume flow used for lag.

Assumptions and limits

  • Steady flow.
  • The cooled sample is at 1 atm; cooling water c_w = 4 186.8 J/(kg·K).
  • The 1.5–2 m/s velocity is common practice, not a cited limit; lower velocities are flagged.
  • At the saturation temperature the sample choice decides the state: saturated water, or dry saturated steam (the duties differ by the latent heat). A water sample above, or a steam sample below, the saturation temperature is rejected. Above the critical pressure the state follows from pressure and temperature alone.

References

  • Continuity for the lag; energy balance with IAPWS-IF97 enthalpies for the cooler

Questions and answers

Why does lag matter?

A long, slow line shows a chemistry upset many minutes after it happened.

Why velocity?

Iron and copper particles settle in slow lines and give low readings.

Steam samples?

Condense and cool to 25 °C so analysers read correctly.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.