Worked example
Example: 10 t/h steam, 10 ppm CO2, morpholine, 5 ppm residual, 40 % solution. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Steam flow | 10,000 kg/h |
| CO₂ in the steam | 10.000 ppm |
| Amine | Morpholine |
| Free amine residual to keep in the steam | 5.0000 ppm |
| Amine content of the product | 40.000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Dose in the steam (active) | 24.796 ppm |
| Active amine feed | 0.24796 kg/h |
| Product feed | 0.61991 kg/h |
| Amine to neutralise 1 kg CO₂ (to bicarbonate) | 1.9796 kg/kg |
Open this example in the calculator and change any input.
Formula
\(r = \frac{M_{amine}}{M_{CO_2}} \qquad D = CO_2\,r + R \qquad \dot m_a = \dot m_s\,D \qquad \dot m_p = \frac{\dot m_a}{w}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot m_s\) | steam flow | kg/s |
| \(CO_2\) | CO₂ in steam, mass fraction | – |
| \(\text{amine}\) | morpholine, cyclohexylamine or ammonia | – |
| \(R\) | free amine residual | – |
| \(w\) | amine content of the product | – |
| \(D\) | dose in the steam | – |
| \(\dot m_a\) | active amine feed | kg/s |
| \(\dot m_p\) | product feed | kg/s |
| \(r\) | amine per kg CO₂ | kg/kg |
| \(M\) | molar masses from IUPAC atomic weights | kg/kmol |
Method and standards
One mole of amine neutralises one mole of CO₂ as bicarbonate; molar masses of morpholine (C₄H₉NO), cyclohexylamine (C₆H₁₃N) and ammonia from IUPAC 2013 atomic weights.
Where it is used
- Condensate corrosion control in process steam plants.
- Estimating amine budgets.
- Checking a supplier's dose recommendation.
Common mistakes
- Dosing amine for oxygen corrosion, which it does not stop.
- Using the product rate as active amine.
- Ignoring food-contact rules where steam touches product.
Assumptions and limits
- CO₂ given as measured in the steam; bicarbonate neutralisation; distribution between phases not modelled.
- Neutralising to bicarbonate is the minimum. Reaching a target condensate pH (often 8.5–9.2) usually needs more amine than the stoichiometric amount; the free residual you enter is where that margin goes.
References
- Neutralisation stoichiometry (amine + CO2 + H2O → amine bicarbonate, 1:1)
- IUPAC 2013 atomic weights
Questions and answers
How much amine neutralises the CO₂ in steam?
For morpholine, 1.98 kg per kg of CO₂ (to bicarbonate). 10 t/h of steam with 10 ppm CO₂ and a 5 ppm free residual needs 24.8 ppm, 0.25 kg/h of morpholine or 0.62 kg/h of a 40 % product.
Why does the far end of the system need more?
Each amine splits between steam and condensate by its distribution ratio; a low-ratio amine protects the first condensate, a high-ratio one travels further. Blends cover both.
Where does the CO₂ come from?
From the breakdown of bicarbonate and carbonate alkalinity in the boiler water. Dealkalising the make-up reduces it at source.
Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.