Worked example
Example: Cooling water 25 °C, pH 8.0, TDS 500, Ca 250, alkalinity 100 mg/L. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Measured pH of the water | 8.0000 - |
| Water temperature | 25.000 °C |
| Total dissolved solids | 500.00 mg/L |
| Calcium hardness as CaCO₃ | 250.00 mg/L |
| Total (M) alkalinity as CaCO₃ | 100.00 mg/L |
Applying the formula below gives:
| Result | Value |
|---|---|
| Saturation pH (calcium carbonate) | 7.5602 |
| Langelier saturation index | 0.43976 |
| Ryznar stability index | 7.1205 |
| Factor A (dissolved solids) | 0.16990 |
| Factor B (temperature) | 2.0883 |
| Factor C (calcium) | 1.9979 |
| Factor D (alkalinity) | 2.0000 |
Open this example in the calculator and change any input.
Formula
\(pH_s = (9.3 + A + B) - (C + D)\)
\(A = \frac{\log_{10}\text{TDS} - 1}{10}, \quad B = -13.12 \log_{10}(t + 273) + 34.55\)
\(C = \log_{10}\text{Ca} - 0.4, \quad D = \log_{10}\text{Alk}\)
\(LSI = pH - pH_s, \quad RSI = 2\,pH_s - pH\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(pH\) | Measured pH of the water | - |
| \(T\) | Water temperature | K |
| \(\text{TDS}\) | Total dissolved solids | kg/m³ |
| \(\text{Ca}\) | Calcium hardness as CaCO₃ | kg/m³ |
| \(\text{Alk}\) | Total (M) alkalinity as CaCO₃ | kg/m³ |
| \(pH_s\) | Saturation pH (calcium carbonate) | - |
| \(LSI\) | Langelier saturation index | - |
| \(RSI\) | Ryznar stability index | - |
| \(A\) | Factor A (dissolved solids) | - |
| \(B\) | Factor B (temperature) | - |
| \(C\) | Factor C (calcium) | - |
| \(D\) | Factor D (alkalinity) | - |
Method and standards
The saturation pH pHs is the pH at which the water would be just saturated with calcium carbonate. The working form above, with TDS, calcium hardness and total alkalinity in mg/L (the last two as CaCO₃) and temperature t in °C, is the one used in water-treatment practice for Langelier's equilibrium. Ryznar's index weights the same pHs to separate scaling from corrosive waters more clearly.
Where it is used
- Cooling tower chemistry: setting cycles of concentration and acid dosing.
- Checking whether softened or RO water will be aggressive to pipework.
- Comparing make-up water sources.
Common mistakes
- Entering calcium as Ca instead of as CaCO₃ (multiply Ca by 2.5).
- Using P alkalinity instead of total (M) alkalinity.
- Using the basin temperature when scaling happens at the hot tube wall.
Assumptions and limits
- 0–100 °C; the working form is approximate at high TDS (above about 10 000 mg/L), and a note appears there.
- A note gives the common reading of the RSI bands.
- An index of tendency only; inhibitors and flow decide what happens.
References
- Langelier (1936)
- J. AWWA 28
- Ryznar (1944)
- J. AWWA 36
- Standard Methods 2330 (calcium carbonate saturation)
Questions and answers
What does a positive Langelier index mean?
The water is supersaturated with calcium carbonate and tends to deposit scale. Cooling water at 25 °C, pH 8.0, TDS 500, calcium 250 and alkalinity 100 mg/L has pHs 7.56 and LSI +0.44.
How is the Ryznar index read?
RSI = 2 pHs − pH. In common reading, below about 6 the water tends to scale, around 6 to 7 it is near balance, and above 7 it tends to be corrosive; the example gives RSI 7.1. The bands are a rule of practice, not exact limits.
Why does the index rise with temperature?
Calcium carbonate is less soluble in hot water, so pHs falls and the same water scales more on hot heat transfer surfaces than in the basin.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.