Worked example
Example: 0.5 mg/L NH3, target pH 9.3. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Ammonia in the water, as NH₃ | 0.50000 mg/L |
| Target pH at 25 °C | 9.3000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| pH at 25 °C from the dose | 9.1927 |
| Share of the ammonia present as free NH₃ | 46.915 % |
| Ammonia needed for the target pH, as NH₃ | 0.72427 mg/L |
| pKa of ammonium at 25 °C | 9.2464 |
Open this example in the calculator and change any input.
Formula
\(pK_a = 0.09018 + \frac{2729.92}{T}, \quad T = 298.15\ \text{K}\)
\([\text{H}^+] + \frac{c\,[\text{H}^+]}{[\text{H}^+] + K_a} = \frac{K_w}{[\text{H}^+]}\)
\(c = \frac{c_{NH_3}}{M_{NH_3}}, \quad f_{NH_3} = \frac{K_a}{[\text{H}^+] + K_a}\)
\(c_{req} = \left(\frac{K_w}{[\text{H}^+]_t} - [\text{H}^+]_t\right) \frac{[\text{H}^+]_t + K_a}{[\text{H}^+]_t}\, M_{NH_3}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(c_{NH_3}\) | Ammonia in the water, as NH₃ | kg/m³ |
| \(pH_t\) | Target pH at 25 °C | - |
| \(pH\) | pH at 25 °C from the dose | - |
| \(f_{NH_3}\) | Share of the ammonia present as free NH₃ | - |
| \(c_{req}\) | Ammonia needed for the target pH, as NH₃ | kg/m³ |
| \(pK_a\) | pKa of ammonium at 25 °C | - |
| \(K_a\) | Dissociation constant of ammonium | mol/L |
| \(K_w\) | Ionic product of water at 25 °C | (mol/L)² |
| \(c\) | Ammonia concentration | mol/L |
| \(M_{NH_3}\) | Molar mass of ammonia | kg/kmol |
| \([\text{H}^+]_t\) | Hydrogen ion concentration at the target pH | mol/L |
Method and standards
The ammonium–ammonia equilibrium constant comes from the Emerson et al. (1975) fit to Bates and Pinching's measurements. The charge balance of pure water with ammonia is solved for the hydrogen ion concentration; the dose for a target pH follows from the same balance in closed form.
Where it is used
- All-volatile treatment of feedwater (AVT).
- Setting an ammonia dosing pump rate.
- Checking condensate pH after ammonia carry-over.
Common mistakes
- Mixing mg/L as NH₃ with mg/L as N (N × 1.216 = NH₃).
- Expecting the same pH at operating temperature.
- Ignoring carbon dioxide in the water, which lowers the pH.
Assumptions and limits
- Pure water plus ammonia at 25 °C; ideal solution.
- Kw = 1.0 × 10⁻¹⁴ (the shared water-chemistry value; the 25 °C value is nearer 1.008 × 10⁻¹⁴, a pH difference of about 0.002–0.004).
References
- Emerson et al. (1975)
- J. Fish. Res. Board Can. 32
- ammonium pKa
- Bates and Pinching (1949)
- ammonium dissociation
Questions and answers
What pH does 0.5 mg/L of ammonia give?
In pure water at 25 °C, pH 9.19; about 47 % of the ammonia is then free NH₃ and the rest ammonium.
How much ammonia gives pH 9.3?
About 0.72 mg/L as NH₃. pH rises slowly with dose because ammonia is a weak base: each 0.1 pH costs more ammonia.
Why at 25 °C only?
Feedwater pH is measured on a cooled sample at 25 °C; at feedwater temperature the same water has a lower pH because water and ammonium both dissociate more.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.