FireCADCalc

Coordinated Phosphate: Sodium-to-Phosphate Molar Ratio

Sodium-to-phosphate molar ratio of boiler water from sodium and phosphate analyses, for coordinated or congruent phosphate treatment control.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolBoiler

Inputs

Examples: Ratio about 3.0Free caustic

Results

Ratio above 3: free caustic (NaOH) is present; caustic gouging risk under deposits.

Molar ratio4.5899
Sodium0.43497mmol/L
Phosphate0.094767mmol/L

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Ratio about 3.0. The inputs, in the units selected above:

InputValue
Sodium6.5000 mg/L
Phosphate as PO₄9.0000 mg/L

Applying the formula below gives:

ResultValue
Molar ratio2.9834
Sodium0.28273 mmol/L
Phosphate0.094767 mmol/L

Open this example in the calculator and change any input.

Formula

\(n_{Na} = \frac{c_{Na}}{M_{Na}}, \quad n_{PO_4} = \frac{c_{PO_4}}{M_{PO_4}}, \quad M_{PO_4} = M_P + 4M_O, \quad \frac{Na}{PO_4} = \frac{n_{Na}}{n_{PO_4}}\)

Variables

Symbol Meaning SI unit
\(c_{Na}\) Sodium kg/m³
\(c_{PO_4}\) Phosphate as PO₄ kg/m³
\(Na:PO_4\) Molar ratio -
\(n_{Na}\) Sodium mol/m³
\(n_{PO_4}\) Phosphate mol/m³
\(M_{Na}\) Atomic mass of sodium (IUPAC) kg/kmol
\(M_{PO_4}\) Molar mass of phosphate kg/kmol
\(M_P\) Atomic mass of phosphorus (IUPAC) kg/kmol
\(M_O\) Atomic mass of oxygen (IUPAC) kg/kmol

Method and standards

Molar ratio.

Where it is used

  • Phosphate programme control.

Common mistakes

  • Phosphate as P used as PO₄.

Assumptions and limits

  • Same sample. With concentrations in kg/m³ and molar masses in kg/kmol the amounts come out in kmol/m³; they are shown in mmol/L (= mol/m³).
  • All sodium is taken as phosphate-associated. Sodium from other salts (chloride, sulphate) raises the ratio and can trigger the free-caustic note falsely.
  • The note below 2.2 is a general screening flag, not a code limit; the control band is the one your chemistry programme sets.

References

  • Molar ratio from IUPAC atomic masses; control band set by the plant's chemistry programme (trisodium phosphate is 3.0)

Questions and answers

Why the ratio?

Trisodium phosphate has Na:PO₄ = 3; staying at or below 3 avoids free caustic.

Why not too low?

Acid phosphates can corrode magnetite.

Which sodium?

Total sodium from all sources, measured on the same sample.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.