FireCADCalc

Boiler Chemical Consumption and Cost per Tonne of Steam

Daily consumption and cost of a boiler water treatment chemical from its dose in feedwater, steam output, blowdown and product strength, per tonne of steam.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserBoilerWater treatment plant

Inputs

Examples: 20 t/h, 4 % blowdown, 10 ppm active, 35 % product, 120/kgPhosphate 50 t/h, 2 %, 3 ppm, 100 %, 90/kgAmine 10 t/h, 5 %, 2 ppm, 40 %, 300/kg

Results

Product used per day (at full output)1.2632kg
Cost per tonne of steam (your currency)1.5789
Cost per year (your currency)94,737
Feedwater flow10.526t/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 20 t/h, 4 % blowdown, 10 ppm active, 35 % product, 120/kg. The inputs, in the units selected above:

InputValue
Steam output20.000 t/h
Blowdown, share of feedwater4.0000 %
Dose of active chemical in feedwater10.000 mg/L
Active content of the product as supplied35.000 %
Price per kg of product (your currency)120.00 -
Operating hours per year8,000.0 h

Applying the formula below gives:

ResultValue
Product used per day (at full output)14.286 kg
Cost per tonne of steam (your currency)3.5714
Cost per year (your currency)571,429
Feedwater flow20.833 t/h

Open this example in the calculator and change any input.

Formula

\(\dot m_{fw} = \frac{\dot m_s}{1 - b} \qquad \dot m_p = \frac{\dot m_{fw}\,c}{\rho_w\,s} \qquad m_d = 86\,400\,\dot m_p \qquad c_t = \frac{\dot m_p\,c_p}{\dot m_s}\cdot 1000\ \mathrm{kg/t} \qquad C_y = \dot m_p\,t_y\,c_p\)

Variables

Symbol Meaning SI unit
\(\dot m_s\) steam output kg/s
\(b\) blowdown share of feed –
\(c\) active dose kg/m³
\(s\) active content of product –
\(c_p\) price per kg currency
\(t_y\) hours per year s
\(m_d\) product per day kg
\(c_t\) cost per tonne of steam currency
\(C_y\) cost per year currency
\(\dot m_{fw}\) feedwater flow kg/s
\(\dot m_p\) product flow kg/s
\(\rho_w\) 1000 kg/m³ (mg/L taken as mg/kg) kg/m³

Method and standards

Mass balance: dose on feedwater flow, product flow from the active content.

Where it is used

  • Treatment programme budgets.
  • Comparing chemical suppliers.
  • Steam cost build-up.

Common mistakes

  • Dosing on steam flow.
  • Using product dose as active dose.
  • Ignoring condensate return quality.

Assumptions and limits

  • Constant dose; full output.
  • The dose is on the whole feedwater. Chemicals dosed to the drum (phosphate, for example) are often specified as a boiler-water residual instead: convert that to a feedwater dose (residual × blowdown share of feedwater) first.

References

  • Mass balance on feedwater (ppm = mg/kg)

Questions and answers

What does a 10 ppm dose cost on 20 t/h with 4 % blowdown?

With a 35 % product at 120 per kg: 14.3 kg of product a day, 3.57 per tonne of steam, 571 000 a year at 8000 h.

Why use feedwater, not steam?

Chemicals go into the feedwater, which is steam plus blowdown.

Is mg/L the same as ppm?

For dilute water, yes: 1 mg/L ≈ 1 mg/kg.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.